Bedienungsanleitung DeWalt DC900KL T 1 (Seite 31 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549644

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

● To select the screwdriving mode, align the collar

(5) with the symbol (16) on the housing.

● To select the rotary drilling mode, align the

collar (5) with the symbol (17) on the housing.

● To select the percussion drilling mode, ﬁ rst

select the rotary drilling mode and then align the

symbol on the collar (4) with the indicator (18) on

the collar (5).

Do not select the operating mode when

the tool is running.

Adjusting the torque (ﬁ g. D)

The collar of this tool has a wide range of positions

for the adjustment of the torque to suit the size of

the screw and the workpiece material. For torque

adjustment, refer to the section "Screwdriving".

● Select the torque by aligning the symbol or

number on the collar (4) with the indicator (18)

on the collar (5).

Forward/reverse slider (ﬁ g. E)

● To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing

the direction of rotation.

Three-gear selector (ﬁ g. F)

Your tool is ﬁ tted with a three-gear selector (6) to

vary the speed/torque ratio.

1 low speed/high torque

2 medium speed/medium torque

3 high speed/low torque

For speed rates, refer to the technical data.

● Do not change gears at full speed or during

use.

Instructions for use

● Always observe the safety instructions

and applicable regulations.

● Be aware of the location of pipework

and wiring.

● Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

● Make sure your battery pack is (fully) charged.

● Make sure the battery pack is properly seated.

● Insert the appropriate bit.

● Mark the spot where the hole is to be drilled.

Switching on and off (ﬁ g. A & E)

● To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

● To stop the tool, release the switch.

● To lock the tool in the off position, move the

forward/reverse slider (2) to the central position.

Screwdriving (ﬁ g. A)

● Select the drilling mode using the collar (5).

● Select forward or reverse rotation using the

slider (2).

● Set the collar (4) to position 1 and begin

screwdriving (low torque).

● If the clutch ratchets too soon, adjust the collar

to increase the torque as required.

Drilling (ﬁ g. A)

● Select the drilling mode using the collar (5).

● Select forward rotation using the slider (2).

Drilling in metal

● Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which

should be drilled dry.

Drilling in wood

● Use the appropriate type of drill bit.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your D E WALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular

cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC900KL T 1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info