Bedienungsanleitung DeWalt DCE080GS (Seite 14 von 232) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790944

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

GB • Use appropriate personal protective equipment, including eye

protection when working in a construction environment.

Tool Use and Care

• Do not use the tool if the switch does not turn it on or off. Any

tool that cannot be controlled with the switch is dangerous and

must be repaired.

• Store idle laser products out of the reach of children and do

not allow persons unfamiliar with the laser product or these

instructions to operate the laser product. Laser products are

dangerous in the hands of untrained users.

• Use only accessories that are recommended by the

manufacturer for your model. Accessories that may be suitable

for one tool, may become hazardous when used with another tool.

Batteries and Power

This DeWALT rotary laser will accept all DeWALT 18 volt lithium ion

battery packs, but is built to best resist damage during a fall when

used with the following battery packs: All 1.5Ah and 2Ah DeWALT 18

volt lithium ion batteries.

Charging the Battery Pack

The battery pack is not fully charged out of the carton. You need to

use a DeWALT 18 volt charger to charge the battery pack before you

can use the rotary laser.

• Be sure to read all safety instructions before using your charger.

WARNING:

DO NOT attempt to charge the battery pack with any

chargers other than the ones listed in this manual. The

charger and battery pack are specifically designed to work

together.

WARNING:

Carefully follow all instructions and warnings on the battery

label and package and accompanying Battery Safety

Manual.

1. Slide the battery pack into the charger as described in the

Battery Safety Manual.

2. Wait until the battery pack is fully charged.

3. Slide the battery pack out of the charger.

NOTE: When ordering replacement battery packs, be sure to include

the catalog number and voltage.

Installing the DeWALT 18V Battery Pack

1. Position the fully-charged DEWALT 18V battery pack so the

release button (Figure D 1) is facing away from you and to the

right.

2. Press and hold down the release button (Figure D 1) on the

battery pack.

3. Slide the battery pack all the way into the track on the side of

the laser (Figure D 2).

4. Release the button on the battery pack.

Removing the Battery Pack

1. Press and hold the release button on the battery pack (Figure

D 1).

2. Slide the battery pack out of the track on the laser.

3. Release the button on the battery pack.

4. To recharge the battery pack, insert it into the charger, as

described in the Battery Safety Manual.

WARNING:

Batteries can explode or leak, and can cause injury or fire.

To reduce this risk, follow the instructions in the Battery

Safety Manual.

Storing Battery Packs

• The best storage place is one that is cool and dry, and away from

direct sunlight and excess heat or cold.

• Long storage will not harm the battery pack or charger. Under

proper conditions, they can be stored for 5 years or more.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE080GS Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info