Bedienungsanleitung DeWalt DCF680 T 1 (Seite 8 von 16) (Englisch)

549690

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

• Do not use an extension cord unless it is absolutely necessary. Use

of improper extension cord could result in risk of fire, electric shock or

electrocution.

• When operating a charger outdoors, always provide a dry location and use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

• Do not place any object on top of the charger or place the charger on a soft

surface that might block the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat source. The charger is

ventilated through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow, been dropped or

otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble the charger; take it to an authorized service center when

service or repair is required. Incorrect reassembly may result in a risk of electric

shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This

will reduce the risk of electric shock. Removing the battery pack will not reduce

this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 230 V household electrical

power. Do not attempt to use it on any other voltage. This does not apply to the

vehicular charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions before using

your charger. Consult the chart at the end of this manual for compatibility of chargers

and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate outlet before

FIG. 1

inserting the battery pack.

2. Insert the battery pack (G) into the charger, as

shown in Figure 1, making sure the pack is fully

seated in charger. The red (charging) light will

blink continuously, indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

Indicator Light Operation

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

Charge Indicators

This charger is designed to detect certain problems that can arise. Problems are indicated

by the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the

charger. If the problem persists, try a different battery pack to determine if the charger

is working properly. If the new pack charges correctly, then the original pack is defective

and should be returned to a service center or other collection site for recycling. If the new

battery pack elicits the same trouble indication as the original, have the charger and the

battery pack tested at an authorized service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF680 T 1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCF680 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info