Bedienungsanleitung DeWalt DCF813 T 3 (Seite 35 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549695

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

• These chargers are not intended for

any uses other than charging DEWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock, or electrocution.

• Do not place any object on top of charger

or place the charger on a soft surface that

might block the ventilation slots and result

in excessive internal heat. Place the charger

in a position away from any heat source. The

charger is ventilated through slots in the top and

the bottom of the housing.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

• Do not operate charger if it has received

a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorised

service centre.

• Do not disassemble charger; take it to an

authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

• In case of damaged power supply cord the

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

• Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on

standard 230V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

SAVE THESE INSTRUCTIONS

Chargers

The DCB100, DCB105, DCB107 and DCB112

chargers accept 10.8 V Li-Ion batteries.

These chargers require no adjustment and are

designed to be as easy as possible to operate.

Charging Procedure (ﬁ g. 2)

1. Plug the charger (k) into an appropriate outlet

before inserting battery pack.

2. Insert the battery pack (f) into the charger.

The red (charging) light will blink continuously

indicating that the charging process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer the tables below for the state of charge of the

battery pack.

State of charge–DCB100 and DCB105

charging – – – –

fully charged –––––––––––

hot/cold pack delay –– – –– –

replace battery pack •••••••••••

State of charge–DCB107 and DCB112

charging –– –– –– –– ––

fully charged ––––––––––––––––––––

hot/cold pack delay –– –– –– –––––––

Hot/Cold Pack Delay

DCB100 AND DCB105

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

DCB107 AND DCB112

When the charger detects a battery that is hot, it

automatically delays charging until the battery has

cooled.

When the charger detects a battery that is cold, it

automatically delays charging until the battery has

warmed.

The red light will continue to blink, but a yellow

indicator light will be illuminated during this

operation. Once the battery has cooled, the yellow

light will turn off and the charger will resume the

charging procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCF813 T 3 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DCF813 T 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info