Bedienungsanleitung DeWalt DCF888 (Seite 35 von 156) (Alle Sprachen)

723570

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

Inserting and Removing the Battery Pack

from the Tool(Fig. B, C)

NOTE: Make sure your battery pack6 is fullycharged.

To Install the Battery Pack into the

Tool Handle

1. Align the battery pack6 with the rails inside the tool’s

handle(Fig. C).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button5 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs(Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Belt Hook and Magnetic Bit

Holder(Fig.A)(Optional Accessories)

WARNING: To reduce the risk of serious personal

injury, ONLY use the tool's belt hook to hang the

tool from a work belt. DO NOT use the belt hook for

tethering or securing the tool to a person or object during

use. DO NOT suspend tool overhead or suspend objects

from the belthook.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

IMPORTANT: When attaching or replacing the belt hook or

magnetic bit holder, use only the screw9 that is provided. Be

sure to securely tighten thescrew.

The belt hook8 and magnetic bit holder13 can be be

attached to either side of the tool using only the screw9

provided, to accommodate left- or right- handed users. If the

hook or magnetic bit holder is not desired at all, it can be

removed from thetool.

To move belt hook or magnetic bit holder, remove the screw9

that holds it in place then reassemble on the opposite side. Be

sure to securely tighten thescrew.

Precision Drive

In addition to normal impacting modes, this tool features

Precision Drive which enables greater control in lighter

applications to avoid damage to materials or fasteners. It is ideal

for light applications such as cabinet hinge screws or machine

screws. Precision Drive will work as a screwdriver in light

applications, before hesitating as the screw head reaches the

work piece, and then(if required) start a slow controlled impact

to ensure the head ends perfectlyflush.

Precision Drive can be customized using the Tool Connect™

app. Refer to Mode Selector table for factorypresets.

NOTE: Precision Drive is for light duty screwdriving applications.

If the tool will not drive a fastener in Precision Drive mode,

please select a different mode that does not have Precision

Drive enabled.

Variable Speed Trigger Switch(Fig.A)

To turn the tool on, squeeze the trigger switch1. To turn the

tool off, release the trigger switch. Your tool is equipped with a

brake. The tool will stop when the trigger switch is fullyreleased.

The variable speed trigger enables you to start the application at

a slow speed. The further you squeeze the trigger, the faster the

tool will operate. For maximum tool life, use variable speed only

for starting holes orfasteners.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should

beavoided.

Forward/Reverse Control Button(Fig.A)

A forward/reverse control button2 determines the direction of

the tool and also serves as a lock-offbutton.

To select forward rotation, release the trigger switch1 and

depress the forward/reverse control button2 on the right side

of thetool.

To select reverse, release the trigger switch1 and depress

the forward/reverse control button2 on the left side of the

tool. The centre position of the control button locks the trigger

switch in the off position. When changing the position of the

control button, be sure the trigger isreleased.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate aproblem.

Quick-Release Chuck(Fig.A, F, G)

WARNING: Use only impact accessories. Non-impact

accessories may break and cause a hazardous condition.

Inspect accessory prior to use to ensure that it con tains

nocracks.

NOTE: The chuck accepts 6.35 mm hex accessoriesonly.

Place the forward/reverse button2 in the lock-off(centre)

position or remove battery pack before changingaccessories.

To install an accessory, push accessory to fully insert into

chuck4. The chuck collar does not need to be pulled back to

lock accessory inplace (Fig.F).

To remove an accessory, pull the chuck collar3 away from the

front of the tool. Remove the accessory(Fig.G).

DeWalt DCF888 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info