Bedienungsanleitung DeWalt DCMWSP564 (Seite 39 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790949

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

ENGLISH

READ THIS INSTRUCTION MANUAL BEFORE

OPERATING YOUR MOWER

Refer to Figure A at the beginning of this manual for a complete

list ofcomponents. Save this manual for futurereference.

DANGER: Sharp moving blade. Do not operate the

mower in mulching mode if the rear door and side

discharge door are not closed under spring tension as

serious injury could result. Take your mower to the nearest

service center forrepair.

Proper hand position requires both hands grasping the main

handle4, and bail handle5.

Proper Hand Position (Fig. L)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Adjusting Mower Height (Fig. G, H)

DANGER: Never attempt to adjust mower height

with the motorrunning.

The height of cut is adjusted by the front and rear cut height

adjustmentlevers11.

NOTE: If you are not sure what height to cut at, begin mowing

with the front and rear cut height adjustmentlevers11,

positioned at the highest settings and adjust the height down

asneeded for yourapplication.

To Set the Height of Cut

1. Pull the rear cut height adjustment lever11 out of the

locking notch25.

2. Move the lever towards the front of the appliance to raise

the height ofcut asdesired.

3. Move the lever towards the rear of the appliance to lower

the height ofcut asdesired.

4. Push the cut height adjustment lever11 into one of the

lockingnotches25 to set theheight.

5. Repeat for the front cut height adjustment lever11

except that the lever is moved towards the rear of

the appliance to raise the height of cut, and towards

the front of the appliance to lower the height of cut.

NOTE: For best results, the front and rear cut height

adjustmentlevers11 should be set to the same

cutheight as indicated by the number next to thenotch.

Mulching (Fig. A, E, F)

DANGER: Turn unit off and remove safety key and

batterypacks.

1. To operate mower in mulching mode, remove the grass

collection bag13.

2. Be sure rear door cover12 isclosed.

3. If installed, remove side discharge chute16 and make sure

side flap15 is fullydown.

Side Discharge (Fig. A, F)

DANGER: Turn unit off and remove safety key and

batterypacks.

1. To operate mower in side discharge mode, remove the grass

collection bag13.

2. Be sure rear door cover12 isclosed.

3. Lift the side flap15 and hook side discharge chute16 onto

themower.

4. Release the side flap and ensure the side discharge

chute16 holds in place before turning moweron.

Grass Collection Bag (Fig. E)

DANGER: Turn unit off and remove safety key and

batterypacks.

1. Lift the rear door cover11 and place the grass collection

bag12 onto the mower so the bag lugs16 slide into

the slots17 on the inside plastic surfaces of the handle

brackets as shown in Fig. G. Then lower the rear doorcover.

2. If installed, remove side discharge chute16 and make sure

side flap15 is fullydown.

Attaching Upper Handle (Fig. A, D)

1. Line up the holes on the bottom of the upper handle4

with the holes on the top of the lower handle17. Take care

to not pinch or stress thecord.

NOTE: Make sure the cord is located on the front of both

handles. If it is not it may result in the cord tangling and the

inability to easily store themower.

2. From the inside of the lower handle4, insert the handle

bolt20 through the two handle holes. Repeat for the

oppositeside.

3. From the outside of the upper handle tighten a handle

knob18 onto each handle bolt20. Take care to not pinch

or stress thecord.

Adjusting Handle Height (Fig. A, C)

The mower is shipped in storage mode. You will need to adjust

the handle to operating position beforecontinuing.

1. To unlock the lower handle17 from the storage position,

twist the two handle lock knobs7 a quarter turn. The

handle lock knobs7 are located on both sides of the lower

handle 17.

2. Raise the lower handle to the operatingposition. Take care

to not pinch or stress thecord.

3. Twist the handle lock knobs7 a quarter turn, securing the

lower handle intoposition.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCMWSP564 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info