Bedienungsanleitung DeWalt DW055 (Seite 29 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

446500

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

WARNING: NEVER use a light socket.

NEVER connect the live (L) or

neutral (N) wires to the earth

pin marked E or

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

Assembly and adjustment

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DEWALT battery

packs and chargers.

Battery pack (ﬁ g. 1)

BATTERY TYPE

The DW052 and DW053 operate on 12 volt battery

packs. The DW054 and DW055 operate on 14.4 volt

battery packs. The DW056 and DW057 operate on

18 volt battery packs.

Charging the battery pack (ﬁ g. 2)

When charging the battery pack (e) for the first time,

or after prolonged storage, it will only accept an

80% charge. After several charge and discharge

cycles, the battery pack will attain full capacity.

Always check the mains prior to charging the battery

pack. If the mains is functioning but the battery pack

does not charge, take your charger to an authorised

EWALT repair agent. Whilst charging, the charger

and the battery pack may become warm to touch.

This is a normal condition and does not indicate a

problem.

WARNING: Do not charge the battery

pack at ambient temperatures < 4 °C

or > 40 °C. Recommended charging

temperature: approx. 24 °C.

To charge the battery pack (e), insert it into the

charger (g) as shown and plug in the charger. Be

sure that the battery pack is fully seated in the

charger. The red charging indicator (h) will blink.

After approx. 1 hour, it will stop blinking and remain

on. The battery pack is now fully charged. The

battery pack can be removed at any time or left in

the connected charger for a longer period of time

(with a maximum of 14 days).

Inserting and removing the

battery pack

1. Insert the battery pack (e) into the grip until it

clicks in place.

2. To remove the battery pack, press the two

release buttons (f) simultaneously and pull the

pack out of the grip.

Battery cap (ﬁ g. 2)

A protective battery cap (i) is supplied to cover the

contacts of a detached battery pack. Without the

protective cap in place, loose metal objects could

short circuit the contacts, causing a fire hazard and

damaging the battery pack.

1. Take off the protective battery cap (i) before

placing the battery pack (e) in the charger

or tool.

2. Place the protective cap over the contacts

immediately after removing the battery pack

from the charger or tool.

WARNING: Make sure the protective

battery cap is in place before storing or

carrying a detached battery pack.

Automatic refresh

The automatic refresh mode will equalize or balance

the individual cells in the battery pack at its peak

capacity. Battery packs should be refreshed

overnight after every 10th charge/discharge cycle

or whenever the pack no longer delivers the same

amount of work.

To refresh your battery pack, place it in the charger

as usual. The red light will blink continuously

indicating that the charge cycle has started.

When the 1-hour charge cycle has completed, the

light will stay on continuously and will no longer

blink. The battery pack is fully charged and can be

used at this time.

If the battery pack is left in the charger after the initial

1-hour charge, the charger will automatically initiate

the refresh mode. This mode will continue up to

8 hours, but the battery pack can be removed at

any time during the refresh mode.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too

hot or too cold, it automatically starts a Hot/Cold

Pack Delay, suspending charging until the battery

has reached an appropriate temperature. The

charger then automatically switches to the pack

charging mode. This feature ensures maximum

battery life. The red indicator blinks long, then short

while in the Hot/Cold Pack Delay mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW055 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info