Bedienungsanleitung DeWalt DW055 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

446500

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

ASSEMBLY

Inserting and removing a bit

(ﬁ g. 1, 4)

DW052, DW054, DW056

The tool uses 1/4" hex. drive system with locking

sleeve.

1. Pull the sleeve/tool holder (c) forward and

insert the bit into the sleeve as far as it will go.

Release the sleeve to secure the bit.

2. To remove the bit, pull sleeve forward and pull

the bit out firmly.

Fitting and removing sockets

(ﬁ g. 1, 4)

DW053, DW055, DW057

The tool uses a 1/2" square drive system with detent

pin.

FITTING SOCKETS

1. Align the hole (j) in the side of the socket with

the detent pin (k) on the anvil.

2. Push the socket (l) onto the anvil/tool holder (c)

until it snaps into place. Tap it lightly if required.

REMOVING SOCKETS

Depress the detent pin (k) through the hole in the

socket and pull the socket off the anvil.

Forward/reverse slider (ﬁ g. 3)

To select forward or reverse rotation, use the

forward/reverse slider (b) as shown (see arrows

on tool).

CAUTION: Always wait until the motor

has come to a complete stand still

before changing the direction of rotation.

The first time the tool is run after changing the

direction of rotation, a click may be heard on

start up.

Instructions for use

WARNING: Always observe the safety

instructions and applicable regulations.

Prior to operation, make sure your battery pack is

(fully) charged.

OPERATION

WARNING: Turn unit off and disconnect

battery pack before installing and

removing accessories, before adjusting

or when making repairs. Lock the trigger

switch when the tool is not in use and

when storing the tool.

Prior to operation

1. Depending on your tool, select the appropriate

bit or socket.

2. To run the tool, press the variable speed switch

(a). The pressure exerted on the variable speed

switch determines the tool speed.

3. To lock the tool in off position, move the

forward/reverse slider (b) to the central position.

To Operate

1. Select forward or reverse rotation using slider

(b).

2. Depending on the application, follow either of

the below instructions.

3. Press the variable speed switch (a).

4. After tightening, check torque with a torque

wrench.

Screwdriving

1. Place the tip of the driver bit in the screw head.

2. Keeping the tool in line with the screw, apply

forward pressure to the tool as it contacts the

work surface.

Nutsetting

1. Place the socket over the head of the bolt or

nut.

2. Hold the tool in line with the fastener.

Tightening time

This tool tightens most fasteners in few seconds.

The proper tightening time in relation to torque must

be determined by experience.

WARNING: Excessive tightening may

damage the tip of the driver bit and the

head of the screw.

Use only dedicated impact accessories with your

tool. Consult your dealer for further information on

the appropriate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW055 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info