Bedienungsanleitung DeWalt DW160 T 2 (Seite 17 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544730

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

en - 3

Your DeWALT tool is double insulated in

accordance with prEN 50144; therefore

no earth wire is required.

Mains plug replacement (U.K. & Ireland

only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DeWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

For 115 V tools, use plugs to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved

triple-core extension cable suitable for the power

input of this tool (see technical data). The minimum

conductor size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

damage to ensure that it will operate properly

and perform its intended function. Check for

misalignment and seizure of moving parts,

breakage of parts and any other conditions that

may affect its operation. Have damaged guards

or other defective parts repaired or replaced as

instructed.

Do not use the tool if the switch is defective.

Have the switch replaced by an authorized

DeWALT repair agent.

20 Have your tool repaired by an authorized

DeWALT repair agent

This Power Tool is in accordance with the

relevant safety regulations. To avoid danger,

electric appliances must only be repaired by

qualified technicians.

Package contents

The package contains:

1 Heavy duty right angle drill

1 Chuck key

1 Chuck key holder

1 Instruction manual

1 Exploded drawing

1 Registration card

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and understand

this manual prior to operation.

Description (fig. A)

Your DeWALT Heavy Duty Right Angle Drill is a

professional Power Tool that has been designed

especially for drilling in confined spaces.

1 Chuck

2 Paddle switch

3 Tool housing

4 Chuck key holder

5 Chuck key

6 Pilot hole

7 Chuck guard

8 Chuck jaws

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW160 T 2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info