Bedienungsanleitung DeWalt DW263K T 4 (Seite 27 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

549014

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

Using an Extension Cable

This 115V unit is intended to be use with a safety

transformer manufactured to BSEN 61558 &

BS4343.

WARNING: NEVER work without a

transformer in place!

If an extension cable is required, use an approved

3–core extension cable suitable for the power input

of this tool (see “Technical Data”).The minimum

conductor size is 1.5 mm

; the maximum length is

30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Fitting and Removing 1/4" Hex Drive

Accessories

Your DEWALT screwdriver has a 1/4" hexagonal

drive system. The drive accessory is retained in the

holder by a ball and a spring which engages in a

groove in the accessory shank.

DW263/DW264/DW274/DW274KN/DW275/DW275KN

(FIG. 1A, 2)

1. Remove the collar (d) by pulling it forward.

2. Select the required accessory (both models)

and matching depth locator (e) when using a

nutsetter (DW263/DW264).

3. To insert the accessory (l), e.g., a bit holder or

nutsetter, push it into the holder (h) until it snaps

in place. Tap it lightly if required.

4. To remove the accessory, pull it out of the

holder using a pair of pliers.

5. Reinstall the collar (d) by aligning the ribs (i) on

the inside of the collar (d) with the grooves (j) in

the clutch housing and snap the collar in place.

DW268/DW269 (FIG. 1B)

1. Pull the ball retainer (g) to the front and hold it.

2. Insert the accessory.

3. Release the ball retainer.

REPLACING THE BIT TIP (FIG. 2)

Simply pull out the bit tip (k). A pair of pliers may be

required.

Driving Depth (ﬁ g. 3)

DW263/DW264/DW274/DW274KN/DW275/DW275KN

The depth sensitive feature offers the following

advantages:

– The selected driving depth is repeatable for

structural integrity.

– Screws with sealing washers are driven correctly

so that no leaks occur.

SETTING THE DRIVING DEPTH

The driving depth is determined by the position of

the depth locator (e) in relation to the bit or socket.

The symbols on the collar (d) indicate how to set the

driving depth.

• Turn the collar (d) clockwise to increase the

driving depth.

• Turn the collar (d) counterclockwise to decrease

the driving depth.

VERSA CLUTCH

UNITS

DW268/DW269 (FIG. 1B)

External adjustment of all Versa Clutch

units for

a wide range of fastener sizes is fast and easy, as

follows:

1. Pull forward, then rotate collar in increase

direction (stamped on adjustment collar) to

increase the amount of clutch engagement and

torque output.

2. Maximum rotation of the collar in the increase

direction results in full clutch engagement and

maximum torque output and fastener capacity.

Collar and adjustable stop will not screw off

clutch housing.

3. Test drive a fastener into a scrap piece to check

proper fastener seating. It is normal after a

period of use to require a slightly different collar

setting due to wear on the clutch faces.

NOTE: With Versa Clutch

, the operator has the

ability to “override” clutch ratchet if a fastener hits a

wood knot, variable hardness in steel work pieces or

incorrect pilot holes. Increased operator pressure will

usually cause the clutches to pick-up and continue

to seat the fastener. Further, a quick twist of the

collar will change the clutch setting to overcome

most driving difficulties and will provide for immediate

change in torque output giving the operator the

option to drive a wide range of fastener sizes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW263K T 4 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DW263K T 4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info