Bedienungsanleitung DeWalt DW274KN T 2 (Seite 22 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

548890

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

en - 4 17

Dead spindle drive clutch

This screwdriver is equipped with a dead spindle

feature; the spindle does not turn until the fastener is

pressed into the workpiece. This enables fasteners

to be placed onto the drive accessory of a running

screwdriver.

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 50144; therefore no

earth wire is required.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

For 115 V units with a power rating exceeding 1500 W,

we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm

. When using a cable reel, always

unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Fitting and removing 1/4" hex. drive accessories

Your DEWALT Screwdriver has a 1/4" hexagonal

drive system. The drive accessory is retained in the

holder by a ball and a spring which engages in a

groove in the accessory shank.

DW263K/DW274K/DW274KN (fig. B)

• Remove the collar (4) by pulling it forward.

• Select the required accessory (both models) and

matching depth locator (5) when using a

nutsetter (DW263).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW274KN T 2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info