Bedienungsanleitung DeWalt DW540 (Seite 24 von 91) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544675

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

ENGLISH

en - 5

Hammering only with spindle lock:

impacting only - for light chipping,

chiselling and demolition applications.

SDS-max

chisels can be locked into 8

different positions (also refer to fig. C):

• Rotate the mode selector (5) until it covers the

safety lock (16).

• Lock the chisel in the required position.

• Rotate the mode selector (5) until it points to the

-symbol.

In this mode the Rotary Hammer can also be

used as a lever to free a jammed drill bit.

• Select the required operating mode by rotating

the mode selector lever (5) over the safety lock

(16) until it points to the symbol.

Inserting and removing SDS-max

accessories

(fig. C)

These models use SDS-max

drill bits and chisels

(refer to the inset in fig. C for a cross-section of an

SDS-max

bit shank).

• Unplug the tool.

• Insert the bit shank into the tool holder locking

sleeve (6) and turn the bit slightly until the sleeve

snaps in position.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (6) and pull the bit out of the tool holder.

Assembling and fitting the side handle

The side handle (8) can be mounted in front or in

rear position on either side of the Rotary Hammer to

suit both RH- and LH-users.

Always operate the Rotary Hammer with

the side handle properly assembled.

Mounting in front position (fig. D)

• Unscrew the side handle (8) and disassemble the

side handle clamp (20).

• Snap the steel ring (17) over the collar (7) behind

the tool holder (6). Squeeze both ends together,

mount the bush (18) and insert the pin (19).

• Place the side handle clamp (20) and screw on

the clamp wheel (9). Do not tighten.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

220/240 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

DW541/DW545 - Setting the electronic speed

and impact control dial (fig. B)

• Turn the dial (2) to the desired level. The higher

the number, the greater the speed and impact

energy. With dial settings from “1” (low) to “7” (full

power) the tool is extremely versatile and

adaptable for many different applications. The

required setting is a matter of experience.

E.g. when using smaller diameter bits or when

drilling into ceramic or brittle materials, set the

dial to position “1” (low).

Selecting the operating mode (fig. B)

Your Rotary Hammer can be used in two operating

modes:

Hammer drilling:

simultaneous rotating and impacting - for

all concrete and masonry drilling

operations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW540 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info