Bedienungsanleitung DeWalt DW543 T 3 (Seite 25 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544673

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

en - 5

• To remove a chisel pull back the tool holder

locking sleeve (6) and pull the chisel out of the

tool holder.

Assembling and fitting the side handle (fig. E)

The side handle (8) can be mounted on either side of

the tool to suit both RH- and LH-users.

Always operate the Demolition Hammer

with the side handle properly assembled.

• Unscrew the side handle clamp knob (9) and

disassemble the side handle (8).

• Snap the steel ring (15) over the collar behind the

tool holder. Squeeze both ends together, mount

the bush (16) and insert the pin (17).

• Fit the side handle (8) and screw on the clamp

knob (9). Do not tighten.

• Rotate the side handle to the desired working

position.

• Lock the side handle mounting assembly in place

by tightening the clamp knob (9).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply approx. 20 kg pressure to the tool.

Excessive force does not speed up

chiselling but decreases tool performance

and may shorten tool life.

Chipping and chiselling (fig. A)

• Set the electronic impact power control dial (2).

• Fit and adjust the side handle (8).

• Set the mode indicator lever (5) to the upright or

rear position.

• Insert the appropriate accessory.

• Rotate the chisel or point by hand to lock it into

one of 8 positions.

• Rotate the mode indicator lever (5) back to the

forward position indicated by the impacting

symbol .

• Press the ON/OFF-switch (1).

• For continuous operation, depress the lock-on

button (10) on the ON/OFF-switch.

• To stop the tool, simply press the ON/OFF-switch

(1) once more. Always switch OFF the tool when

work is finished and before unplugging.

Various types of SDS-max

chisels are available as an

option.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

The Demolition Hammer is not user-serviceable. Take

the tool to an authorized DEWALT repair agent as

soon as the service indicator LED (4) lights up.

Lubrication

Your Power Tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean the

housing with a soft cloth.

Accessory maintenance

Accessory maintenance at the right time guarantees

optimal results in application and a long and efficient

accessory life.

• Grind the chisels on grinding disks. Refer to fig. F

for the appropriate angles of the following chisels:

- spade-shaped chisel (18)

- cold chisel (19)

- pointed chisel (20)

- U-shaped chisel (21)

- hollow chisel (22)

- mortar chisel (23)

- toothed chisel (24)

• These chisels can be reground only a

limited number of times. If in doubt,

contact your dealer for recommendations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW543 T 3 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info