Bedienungsanleitung DeWalt DW625E T 6 (Seite 32 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546433

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

Fine Adjustments (ﬁ g. 6)

When not using a depth template, or if the depth of

cut needs readjustment, it is recommended to use

the fine adjuster (q).

1. Adjust the depth of cut using the fine

adjuster (q).

2. Read the depth of cut using the measuring lens

(l) and scale (m).

3. Adapt the depth of cut to the millimeter using

the handwheel (k).

Depth Adjustment with the Router

Installed in Inverted Position (ﬁ g. 4)

1. Remove the cap nut (aa) and the knurled knob

(i) and replace it with the height adjusting tool

(DE6966) available as an option.

2. Screw the threaded end of the height adjusting

tool to the threaded spindle (g).

3. Set the depth of cut using the adjuster on the

height adjusting tool.

WARNING: For installing the router

in inverted position, refer to the relevant

instruction manual on the stationary tool.

Fitting the Parallel Fence (ﬁ g. 1A, 7)

1. Fit the guide rod (f) to the router base (u).

2. Slide the parallel fence (s) over the rods.

3. Tighten the locking bolts (e) temporarily.

Adjusting the Parallel Fence

(ﬁ g. 1A, 7)

1. Draw a cutting line on the material.

2. Lower the router carriage until the cutter is in

contact with the workpiece.

3. Tighten the plunge lock (n) and limit the carriage

return using the knurled nut (i).

4. Position the router on the cutting line.

5. Slide the parallel fence (s) against the workpiece

and tighten the locking bolts (e).

6. Adjust the parallel fence using the fine adjuster

(r). The outer cutting edge of the cutter must

coincide with the cutting line.

7. If required, loosen the screws (bb) and adjust

the strips (cc) to obtain the desired guiding

length.

Fitting the Baseplate Extension

(Option) (ﬁ g. 1B, 8)

1. Fit the baseplate extension (v) to the free end of

the guide rods.

2. Guide the tool with one hand on the knob (w)

and the other on the opposite grip (j).

Fitting a Guide Bush (ﬁ g. 9)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

• Fit the guide bush (ee) to the router base (u)

using the screws (ff) as shown.

Connecting a Dust Extractor

(ﬁ g. 1A, 10)

The dust extraction adaptor consists of a main

section (hh), a cover (ii), a hose guide (jj), two screws

(kk) and two nuts (ll).

1. Slide the cover (ii) onto the main section (hh)

and let it click into place.

2. Connect a dust extractor hose to the dust

extraction adaptor.

3. Loosen the screw in the top of the router and fit

the hose guide (jj) as shown.

Prior to Operation

1. Check that the cutter is correctly installed in the

collet.

2. Set the cutting depth.

3. Connect a dust extractor.

4. Make sure the plunge limiter is always locked

before switiching on.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW625E T 6 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info