Bedienungsanleitung DeWalt DW625E T 6 (Seite 33 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

546433

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Always move your router as indicated

in fig. L (outer edges/inner edges).

Proper Hand Position (ﬁ g. 1, 12)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the each

grip (j), as shown.

Switching On and Off (ﬁ g. 1A, 4)

1. On: pull the switch (a) up.

2. Off: press the switch (a) down.

WARNING: Loosen the plunge limiter

and allow the router carriage to regain

its rest position before switching off.

Using the Guide Bushes (ﬁ g. 9)

1. Secure the template to the workpiece using end

clamps.

2. Select and install an appropriate guide bush

(ee).

3. Subtract the diameter of the cutter from the

outside diameter of the guide bush and divide

by 2. This is the difference between template

and workpiece.

WARNING: If the work piece is not thick

enough, place it on a piece of waste

wood.

Guiding Off a Batten

Where an edge guide cannot be used, it is also

possible to guide the router along a batten clamped

across the workpiece (with an overhang at both

ends.)

Freehand Routing

Your router can also be used without any sort of

guide, e.g. for signwriting or creative work.

WARNING: Make shallow cuts only!

Use cutters with a max. diameter of

6 mm.

Routing with Pilot Cutters (ﬁ g. 2)

Where a parallel guide or guide bush are

inappropriate, it is possible to use pilot cutters (x) for

cutting shaped edges.

These include collets (6 - 12.7 mm), a height

adjusting tool and router table for use in inverted

position, finger jointing tools for dovetail and finger

jointing jigs, dovetail jointing templates, adjustable

guide bush holder and guide bushes and guide rails

in various lengths.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW625E T 6 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info