Bedienungsanleitung DeWalt DW711 T 6 (Seite 28 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

545012

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

Additional Safety Rules for Sawing in Table Saw

Mode

• Never cut when riving knife and/or top guard are removed.

WARNING! The design does not allow the use as bench saw

as long as the U-shaped guard is not mounted.

• Always use the push stick. Never cut workpiece smaller than 30 mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 50 mm by width 400 mm by length 500 mm.

– Greater workpiece needs to be supported by suitable additional

table.

• Always adjust the sliding fence correctly to avoid contact with the lower

guard.

• Do not use saw blades with a body thickness greater or a width of

tooth smaller than the thickness of the riving knife.

• Ensure that the table is securely fixed.

• Always keep the push stick (58) in its place when not in use (fig. A2).

• Replace the table insert when worn.

• Slotting, rebating or grooving is not allowed.

• During transportation make sure that the upper part of the saw blade is

covered, e.g. by the guard.

• Do not use the guard for handling or transportation.

• Do not remove the saw bench table when adjusting the riving knife.

Mitre Saw Mode

• Ensure that the upper portion of the saw blade is completely enclosed

in the mitre sawing mode. Never remove the upper blade guard when

using the machine in mitre saw mode.

• Never cut workpiece shorter than 20 mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 40 mm by width 140 mm by length 400 mm

– Longer workpieces need to be supported by suitable additional

table.

• Always clamp the workpiece safely.

• When performing vertical straight cross-cuts, adjust the sliding fence

correctly to ensure a clearance of max. 5 mm between the saw blade

and the fence (fig. O).

• When performing mitre, bevel or compound mitre cuts, adjust the

sliding fence to ensure the correct clearance for the application (fig. P).

• Ensure that the upper portion of the saw blade is completely enclosed

in the mitre sawing mode.

• Refrain from removing any cut-offs or other parts of the workpiece from

the cutting area while the saw is running and the saw head is not in the

rest position.

Residual Risks

The following risks are inherent to the use of saws:

– injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot

be avoided.

These are:

– Impairment of hearing.

The following factors are of influence to noise production:

~ the material to be cut;

~ the type of saw blade;

~ the feed force.

– Risk of accidents caused by the uncovered parts of the rotating saw

blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

The following factors are of influence to dust exposure:

– worn saw blade;

– dust extractor with air velocity less than 20 m/s;

– workpiece not exactly guided;

– Insufficient dust extraction caused by uncleaned exhaust filters.

Markings on Tool

The following pictograms are shown on the tool:

Read the instruction manual before use.

When using the machine in the mitre saw mode,

make sure that the upper part of the saw blade is

fully covered by the upper saw blade guard.

Only use the machine when the bench saw table is in

highest position.

When using the machine in the bench saw mode,

make sure that the upper and lower guards are in

place. Only use the machine when the bench saw

table is in horizontal position.

Carrying point.

NEVER use the machine in table saw mode when

upper saw blade guard and fixed lower guard are not

mounted.

DATE CODE POSITION (FIG M)

The Date Code (59), which also includes the year of manufacture, is printed

into the housing.

Example:

2010 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Assembled table top mitre saw

1 Parallel rip fence

1 Guard for bench saw position

1 Bottom guard for bench saw position

1 Push stick

1 Hex key 4/6 mm

1 Hex key 5 mm

1 Two-pin spanner

1 Dust extraction adapter for top guard

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may

have occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (ﬁ g. A1–A5)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

1 On/off switch

2 Head lock up release lever

3 Additional saw bench table locking knob

4 Moveable lower blade guard

5 Fixed table

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW711 T 6 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info