Bedienungsanleitung DeWalt DW716E (Seite 36 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546159

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

• To set the additional 1/4°, squeeze the mitre arm lock and carefully

move the arm to the right until the 1/4° vernier mark aligns with the

closest degree mark on the mitre scale. In this example, the closest

degree mark on the mitre scale happens to be 25°. Fig. Q3 shows a

setting of 24-1/4° right mitre.

• When mitring to the right:

– increase the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the right.

– decrease the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the left.

• When mitring to the left:

– increase the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the left.

– decrease the mitre angle by moving the arm to align the

appropriatevernier mark with the closest mark on the mitre scale to

the right.

Cutting Base Mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying flat on the saw.

Inside corner

– Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

– Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

Outside corner

– Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

– Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Cutting Crown Mouldings

The cutting of crown moulding is performed in a compound mitre. In order

to achieve extreme accuracy, your saw has pre-set angle positions at 31.62°

mitre and 33.85° bevel. These settings are for standard crown mouldings

with 52° angles at the top and 38° angles at the bottom.

• Make test cuts using scrap material before doing the final cuts.

• All cuts are made in a left bevel and with the back of the moulding

against the base.

Inside corner

– Left side

• Top of the moulding against the fence.

• Mitre right.

• Save the left side of the cut.

– Right side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

Outside corner

– Left side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the right side of the cut.

– Right side

• Top of the moulding against the fence.

• Mitre right.

• Save the right side of the cut.

Dust extraction (

fig. A2, A3)

• Fit the dustbag (24) onto the dust spout (16).

• Whenever possible, connect a dust extraction device designed in

accordance with the relevant regulations regarding dust emission.

Saw blades

To obtain the stated cutting capacities, always use 305 mm saw blades with

30 mm arbor holes.

Cutting non-ferrous metals

When cutting non-ferrous metals, the machine is only to be used in the mitre

saw mode. We recommend that bevel and compound mitre cuts should

not be performed in non-ferrous metals. The machine is not to be used for

cutting ferrous metals.

• Always use a material clamp when cutting non-ferrous metals. Make

sure that the workpiece is clamped securely.

• Only apply saw blades that are qualified for cutting non-ferrous metals.

• When using lubricants, only apply wax or separation spray. Do not use

emulsions or similar fluids.

• Connect an FI or DI switch between machine and mains to avoid

residual risks caused by metal swarf.

The FI switch should comply with the following specifications:

rated voltage 230 V

rated current 16 A

reaction time < 15 ms

fusing current 30 mA

The DI switch should comply with the following specifications:

DIN VDE 0661

rated voltage 230 V

rated current 16 A

fusing current 30 mA

all-pole cutoff L+N+PE

PE monitoring

low-voltage release

Transporting (fig. A2, B)

In order to conveniently carry the mitre saw, a carrying handle (9) has been

included on the top of the saw arm.

• To transport the saw, lower the head and depress the lock down pin (18).

• Always use the carrying handle (9) or the hand indentations (22) shown

in fig. A2 to transport the saw.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing set-ups

or when making repairs. Be sure the trigger switch is in the OFF

position. An accidental start-up can cause injury.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW716E Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info