Bedienungsanleitung DeWalt DW718 T 2 (Seite 29 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546169

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

Safety instructions

When using stationary power tools, always observe the safety

regulations applicable in your country to reduce the risk of fire,

electric shock and personal injury.

Read all of this manual carefully before operating the tool.

Save this manual for future reference.

General

1 Keep work area clean

Cluttered areas and benches can cause accidents.

2 Consider work area environment

Do not expose the tool to rain. Do not use the tool in damp or wet

conditions. Keep the work area well lit (250 - 300 Lux). Do not use the

tool where there is a risk of causing fire or explosion, e.g. in the

presence of flammable liquids and gases.

3 Keep children away

Do not allow children, visitors or animals to come near the work area or

to touch the tool or the mains cable.

4 Dress properly

Do not wear loose clothing or jewellery, as these can be caught in moving

parts. Wear protective hair covering to keep long hair out of the way.

When working outdoors, preferably wear suitable gloves and non-slip

footwear.

5 Personal protection

Always use safety glasses. Use a face or dust mask whenever the

operations may produce dust or flying particles. If these particles might

be considerably hot, also wear a heat-resistant apron. Wear ear

protection at all times. Wear a safety helmet at all times.

6 Guard against electric shock

Prevent body contact with earthed or grounded surfaces (e.g. pipes,

radiators, cookers and refrigerators). When using the tool under

extreme conditions (e.g. high humidity, when metal swarf is being

produced, etc.), electric safety can be improved by inserting an

isolating transformer or a (FI) earth-leakage circuit-breaker.

7 Do not overreach

Keep proper footing and balance at all times.

8 Stay alert

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

9 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees both

hands to operate the tool.

10 Connect dust extraction equipment

If devices are provided for the connection of dust extraction and

collection facilities, ensure that these are connected and properly used.

11 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

12 Extension cables

Before use, inspect the extension cable and replace if damaged.

When using the tool outdoors, only use extension cables intended for

outdoor use and marked accordingly.

13 Use appropriate tool

The intended use is described in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Do not force the tool.

Warning! The use of any accessory or attachment or performance of

any operation with this tool other than those recommended in this

instruction manual may present a risk of personal injury.

14 Check for damaged parts

Before use, carefully check the tool and mains cable for damage.

Check for misalignment and seizure of moving parts, breakage of

parts, damage to guards and switches and any other conditions that

may affect its operation.

Ensure that the tool will operate properly and perform its intended

function. Do not use the tool if any part is damaged or defective.

Do not use the tool if the switch does not turn it on and off. Have any

damaged or defective parts replaced by an authorised DEWALT repair

agent. Never attempt any repairs yourself.

15 Unplug tool

Switch off and wait for the tool to come to a complete standstill before

leaving it unattended. Unplug the tool when not in use, before changing

any parts of the tools, accessories or attachments and before

servicing.

16 Avoid unintentional starting

Be sure that the tool is switched off before plugging in.

17 Do not abuse cord

Never pull the cord to disconnect from the socket. Keep the cord away

from heat, oil and sharp edges.

18 Store idle tools

When not in use, tools must be stored in a dry place and locked up

securely, out of reach of children.

19 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Keep all handles and switches dry, clean and free from oil

and grease.

20 Repairs

This tool is in accordance with the relevant safety regulations.

Have your tool repaired by an authorised DEWALT repair agent.

Repairs should only be carried out by qualified persons using original

spare parts; otherwise this may result in considerable danger to the user.

Additional safety rules for mitre saws

• Make sure all locking knobs and clamp handles are tight before starting

any operation.

• Do not operate the machine without the guard in position, or if the

guard does not function or is not maintained properly.

• Never use your saw without the kerf plate.

• Never place either hand in the blade area when the saw is connected

to the electrical power source.

• Never attempt to stop a machine in motion rapidly by jamming a tool or

other means against the blade; serious accidents can be caused

unintentionally in this way.

• Before using any accessory consult the instruction manual.

The improper use of an accessory can cause damage.

• Select the correct blade for the material to be cut.

• Observe the maximum speed marked on the saw blade.

• Use a holder or wear gloves when handling a saw blade.

• Ensure that the saw blade is mounted correctly before use.

• Make sure that the blade rotates in the correct direction.

Keep the blade sharp.

• Do not use blades of larger or smaller diameter than recommended.

For the proper blade rating refer to the technical data. Use only the

blades specified in this manual, complying with EN 847-1.

• Consider applying specially designed noise-reduction blades.

• Do not use HSS blades.

• Do not use cracked or damaged saw blades.

• Do not use any abrasive discs.

• Raise the blade from the kerf in the workpiece prior to releasing the switch.

• Ensure that the arm is securely fixed when performing bevel cuts.

• Do not wedge anything against the fan to hold the motor shaft.

• The blade guard on your saw will automatically raise when the arm is

brought down; it will lower over the blade when the arm is raised.

The guard can be raised by hand when installing or removing saw

blades or for inspection of the saw. Never raise the blade guard

manually unless the saw is switched off.

• Keep the surrounding area of the machine well maintained and free of

loose materials, e.g. chips and cut-offs.

• Check periodically that the motor air slots are clean and free of chips.

DeWalt DW718 T 2 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info