Bedienungsanleitung DeWalt DW721KN T 2 (Seite 33 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546511

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

• Before use, ensure the guards, brake, automatic return and locking

devices are functioning properly. Do not use the machine if these

devices are defective.

• When sawing a round workpiece ALWAYS use suitable jig or prism

to prevent rotation of the workpiece.

• Do not force the cutting action. (Stalling or partial stalling of the

motor can cause major damage.) Allow the motor to reach full

speed before cutting.

• Do not lift the machine by its worktable.

• Do not cut ferrous metals, non-ferrous metals or masonry.

• Do not apply lubricants to the blade when it is running.

• Do not place either hand in the blade area when the saw is

connected to the power source.

• Do not reach around behind the saw blade when in use.

• Do not place hands closer than 150 mm from the saw blade while

cutting.

• Do not use damaged or cracked saw blades.

• Replace the fence if damaged and/or no longer offers proper

support. The fence needs to be replaced periodically.

• ALWAYS ensure safe operation. The radial arm saws needs to be

fixed to the floor with diameter 8 mm bolts with a minimum length

of 80 mm.

WARNING! When cutting round workpiece it is necessary

to secure the workpiece against rotation by using jig or

holder.

• Do not use the machine in locations where the temperature may

reach –5˚ or 40˚ C. Suitable temperature is 20˚ C.

• Operators shall be instructed on factors influencing exposure to

noise (e.g. use of saw blade designed to reduce the emitted noise

and machine maintenance). Report faults in the machine, including

guards or saw blade, as soon as they are discovered. Ensure the

operator is adequately trained in use, adjustment and operation of

the machine.

• Connect the machine to a dust collection device when sawing

wood. Always consider factors which influence exposure of dust

such as:

– Type of material to be machined (chip board produces more

dust than wood).

– Correct adjustment of saw blade.

– Ensure that the local extraction as well as hoods, baffles and

chutes are properly adjusted.

• Always wear working gloves when servicing the machine, handling

rough workpieces or changing the saw blade.

• If a voltage failure occurs under idle condition, release the handle

immediately ensuring the saw head moves automatically back to its

rest position.

WARNING! Defect electrical wiring needs to be replaced

immediately.

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting or

changing set-ups or when making repairs. Be sure the

switch is in the OFF position An accidental start-up can

cause injury.

• Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the saw blade is blocked due to abnormal feed force during

cutting, turn the machine off and disconnect it from power supply.

Remove the workpiece and ensure that the saw blade runs free.

Turn the machine on and start new cutting operation with reduced

feed force.

Residual Risks

The following risks are inherent to the use of radial arm saws:

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be

avoided.

These are:

– Injuries caused by touching rotating parts.

– Impairment of hearing.

– Risk of accidents caused by the uncovered parts of the rotating

saw blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

When the power cord is damaged disconnect the plug

from the power source immediately.

Always disconnect the plug before making any

adjustments or perform service/maintenance.

Package Contents

The package contains:

1 Partly assembled radial arm saw

2 Table strips (1 right,1 left)

2 Fences (1 right, 1 left)

2 Table extensions (1 right, 1 left)

1 Dust shroud

1 Box containing:

1 legstand

(4 legs, 4 traverse rails, 24 M8 x 16 bolts, 24 M8 nuts

and 48 D8 flat washers)

1 Skinpack containing:

1 spanner 10/13 mm

1 spanner 22 mm

1 socket wrench 13 mm

4 hex keys (3, 4, 5, 6 mm)

1 height adjustment crank

1 M4.2 x 16 cross head screw

4 table extension supports

19 M8 x 25 bolts

19 D8 flat washers

19 M8 nuts

1 rubber insert

6 wood inserts

3 M8 x 16 screws

3 D8 washers

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may

have occurred during transport.

• Take the time to thoroughly read and understand this manual prior

to operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW721KN T 2 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info