Bedienungsanleitung DeWalt DW721KN T 2 (Seite 34 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546511

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

Description (ﬁ g. 1)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

a. On/off switch

b. Handle

c. Front guard

d. Lower guard

e. Fixed table top

f. Traverse rails

g. Leg

h1. Left fence (small)

h2. Right fence (large)

i. Dust shroud

j. Mitre latch lever

k. Mitre clamp lever

l. Height adjustment crank

m. Radial arm

n. End-cap

o. Cable

p. Dust outlet

q. Yoke assembly

r. Motor

s1. Left table strip

s2. Right table strip

t1. Left table extension

t2. Right table extension

u. Bevel scale

v. Roller head assembly

w. No-volt release switch

x. Electronic control box

INTENDED USE

The radial arm saw has been designed for professional woodworking.

This high precision machine can be easily and quickly set to crosscut,

bevel, mitre. For optimum safety, all major controls have both a latch

and a locking device. Also refer to the quick reference chart at the end

of the section. This saw is designed for use with a 300 mm diameter

carbide tip blade.

DO NOT use under wet conditions or in presence of flammable liquids

or gases.

The radial arm saw is a professional power tool.

DO NOT let children come into contact with the tool. Supervision is

required when inexperienced operators use this tool.

Electrical Safety

The electric motor has been designed for one voltage only. Always

check that the power supply corresponds to the voltage on the rating

plate.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the DEWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

SINGLE-PHASE ONLY

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the new plug.

• Connect the blue lead to the neutral terminal.

• Connect the green/yellow lead to the earth terminal.

WARNING: Follow the fitting instructions supplied with

good quality plugs. Recommended fuse: 13 A.

WARNING: This product must be earthed. Always check

that the power supply corresponds to the voltage on the

rating plate.

Contact a qualified electrician if a new CEE 16 A industrial plug needs

to be fitted.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary.

Use an approved extension cable suitable for the power input of your

machine (see technical data). When using a cable reel, always unwind

the cable completely. The maximum cable length is 30m.

SINGLE-PHASE MACHINES

Use an approved 3-core extension cable suitable for the power input

of this machine (see technical data). The minimum conductor size is

1.5mm².

THREE-PHASE MACHINES

Please ensure the cable is provided with CEE 16A industrial plug/

coupler 5 poles (neutral must be connected) according to IEC 60309.

Voltage Drops

Inrush currents cause short-time voltage drops. Under unfavourable

power supply conditions, other equipment may be affected.

If the system impedance of the power supply is lower than 0.25 Ω,

disturbances are unlikely to occur.

Sockets used for these machines shall be fused with 16 Amperes

cut-out with an inert characteristic.

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting or

changing set-ups or when making repairs. Be sure the

switch is in the OFF position. An accidental start-up can

cause injury.

WARNING: For optimum performance of your saw, it is of

vital importance to follow the procedures in the paragraphs

below.

Set Up

MOUNTING THE HEIGHT ADJUSTMENT CRANK (FIG. 1, 2)

1. Apply the height adjustment crank (l) with the cross head screw.

NOTE: Automatic return arm may need to be moved to allow

height adjustment.

2. Raise the height adjustment crank high enough to provide

clearance for removal of various elements under the motor.

ASSEMBLING THE LEGSTAND (FIG. 1, 3, 4)

The legstand components and fasteners are packed separately.

1. Remove all parts from the package.

2. Lock the arm using the mitre clamp lever (k).

3. Tilt the machine carefully from the pallet until the rear of the column

is resting on the floor.

4. Place a piece of wood (y) under the edge of the table (fig.3).

5. Assemble the legs (g) as shown using the nuts, bolts and flat

washers provided.

NOTE: Do not tighten.

6. Mount the traverse rails (f) (fig. 4).

7. Firmly tighten all fasteners.

8. Tilt the assembly to upright position.

WARNING: The machine must be level and stable at all

times.

IMPORTANT: Assistance may be required to lower and raise

assembly.

MOUNTING THE AUTOMATIC RETURN (FIG. 1, 5–10)

1. The automatic return comes partially assembled as shown in

figure 5.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW721KN T 2 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info