Bedienungsanleitung DeWalt DW743 T 6 (Seite 29 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546233

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

20 en - 3

ENGLISH

• Allow the motor to reach full speed before cutting.

• Raise the blade from the kerf in the workpiece prior to releasing the

switch.

• Do not wedge anything against the fan to hold the motor shaft.

• Never place either hand in the blade area when the saw is connected

to the electrical power source.

• Do not attempt to cut excessively small pieces.

• Never attempt to stop a machine in motion rapidly by jamming a tool or

other means against the blade; serious accidents can be caused

unintentionally in this way.

• Do not use cracked or damaged saw blades.

• Do not use any abrasive discs.

Additional safety rules for saw benches

• Make sure that the blade rotates in the correct direction and that the

teeth are pointing to the front of the saw bench.

• Be sure all clamp handles are tight before starting any operation.

• Be sure all blade and flanges are clean and the recessed sides of the

collar are against the blade. Tighten the arbor nut securely.

• Keep the saw blade sharp and properly set.

• Make sure that the riving knife is adjusted to the correct distance form

the blade - 3-8 mm.

• Never operate the saw without the upper and lower guards in place.

• Keep your hands out of the path of the saw blade.

• Disconnect the saw from the mains supply before changing blades or

carrying out maintenance.

• Use a push stick at all times, and ensure that you do not place hands

closer than 150 mm from the saw blade while cutting.

• Do not attempt to operate on anything but the designated voltage.

• Do not apply lubricants to the blade when it is running.

• Do not reach around behind the saw blade.

Residual risks

The following risks are inherent to the use of this saw:

- Injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be

avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the rotating saw

blade.

- Risk of injury when changing the blade.

- Risk of squeezing fingers when opening the guards.

- Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

Package contents

The package contains:

1 Partly assembled machine

4 Legs

1 Top guard for bench saw position

1 Under-table guard for mitre saw position

1 Plastic bag containing:

1 pin spanner

1 Allen key 6 mm

1 Skinpack containing:

1 dual height rip fence (DE3743)

1 push stick

1 30 teeth TCT saw blade

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

• Remove the saw from the packaging material carefully.

Description (fig. A1 - A4)

Your DEWALT flip-over sawing machine has been designed to operate as a

mitre saw or as a saw bench to perform the four main sawing operations of

ripping, cross-cutting, bevelling and mitring easily, accurately and safely,

using the following materials: wood, wood products, aluminium and plastic.

Mitre saw mode

In mitre saw mode, the sawing machine is used in vertical, mitre or bevel

position.

Saw bench mode

Turned over on its central axis, the sawing machine is used to perform the

standard ripping operation and for sawing wide pieces by manually

feeding the workpiece into the blade.

1 On/off-switch

1A Trigger switch

2 Side panel

3 Leg clamping wingnut

4 Leg

5 Foot

6 Mitre saw table

7 Fence

8 Rotating table location plunger

9 Fixed lower rear guard

10 Fixed upper blade guard

11 Dust extraction adapter

12 Head lock release lever

13 Blade bolt

14 Outer flange

15 Moving lower guard

16 Rotating table

17 Rotating table clamp

18 Mitre scales

19 Table release lever

20 Control handle

21 Depth stop rod

22 Height adjuster

23 Dust extraction adapter

24 Bevel clamp handle

25 Saw table retention bracket

26 Table locking device

27 Riving knife clamp knob

28 Motor housing

Saw bench mode

29 Upper blade guard

30 Riving knife

31 Saw bench table

32 Mitre fence (optional)

33 Dual height parallel fence

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW743 T 6 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info