Bedienungsanleitung DeWalt DW743 T 6 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546233

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

en - 4 21

Optional accessories

For use in mitre saw mode:

32 Mitre fence (DE3496)

34 Adjustable stand 760 mm (max. height) (DE3474)

35 Support guide rails 1,000 mm (DE3494)

35 Support guide rails 500 mm (DE3491)

36 Inclinable support (DE3495)

37 Swivelling stop (DE3462)

38 Length stop for short workpieces (to be used with guide rails [35])

(DE3460)

39 Support with removable stop (DE3495)

40 Support with stop removed (DE3495)

41 Material clamp (DE3461)

42 Roller support table (DE3497)

For use in saw bench mode:

43 Extension table (DE3472)

44 Single sliding table (DE3471)

Push sticks (DE3454) (not shown)

For use in all modes:

45 Three way dust extraction kit (DE3500)

Cutting capacities

Cutting capacity in mitre saw mode

Cutting angle Size of material Notes

H mm B mm

Straight cross-cut 20 180 No packaging piece required

30 176

40 170

68 140

85 68 With 25 mm packaging piece (fig. B1)

88 22 With 50 mm packaging piece (fig. B1)

15 210 Thin boards only (fig. B2)

Table turned 45° to

right for mitre cuts 70 95 Cross-cut at max. height

Table turned 45° to

left for mitre cuts 68 93 Cross-cut at max. height

Sawhead tilted 45°

for bevel cuts 50 140

Cutting capacity in saw bench mode

Cutting depth adjustment

90° vertical cut 0 - 70 mm

45° bevel cut 0 - 32 mm

Electrical safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Mains plug replacement (U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

EWALT authorized repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2), blue is for

Neutral (N) (4) and green/yellow is for Earth (E).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

leads are correctly fixed at the terminal screws.

Never use a light socket. Never connect the live (L) or neutral (N)

wires to the earth pin marked E or

Using an extension cable

If an extension cable is required, use an approved extension cable suitable

for the power input of this machine (see technical data). The minimum

conductor size is 1.5 mm

. When using a cable reel, always unwind the

cable completely. Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.515 25 30 45 60

Voltage Amperes Cable rating (Amperes)

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

115-120 12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always unplug the tool.

The machine is packed in the saw bench mode for compactness and is

fully assembled for mitre saw operation except for the legs, under-table

plastic guard and blade.

Fitting the legs (fig. C)

• Place the machine upside down on the floor.

• Loosen the four wingnuts (3) and insert a leg (4) into each of the clamps.

• Tighten the wingnuts (3) and turn the table over. Make sure it is level;

adjust the leg clamping height if required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW743 T 6 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info