Bedienungsanleitung DeWalt DWE4120 (Seite 44 von 208) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712337

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

english

2. Align the lugs(K) with the notches(L).

3. Press the guard(F) down and rotate it to the

required position.)

4. Securely tighten the screw(N).

5. To remove the guard, slacken the screw.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard to

a service centre to repair or replace the

guard.

MOUNTING CLOSED (TYPE 1) GUARD

WARNING: If present, the One-Touch

guard screw, lever, and spring must be

removed before attempting to mount

the closed (Type 1) guard. The removed

parts must be retained and reinstalled

to use the One-Touch guard. Noting

the position of these parts before

disassembly will aid in reassembly.

1. Open the guard latch. Align the lugs(K) on the

guard with the slots(L) on the gear case.

2. Push the guard down until the guard lug

engages and rotates freely in the groove on the

gear case hub.

3. Rotate guard into desired working position.

The guard body should be positioned between

the spindle and the operator to provide

maximum operator protection.

4. Close the guard latch to secure the guard on

the gear case cover. You should be unable to

rotate the guard by hand when the latch is in

closed position. If rotation is possible, tighten

the adjusting screw with the clamp lever in the

closed position. Do not operate grinder with a

loose guard or clamp lever in open position.

5. To remove the guard, open the guard latch,

rotate the guard so that the arrows are aligned

and pull up on the guard.

NOTE: If, after a period of time the closed (Type 1)

guard becomes loose, tighten the adjusting screw

with the clamp lever in the closed position.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to authorized repair agent to repair or

replace the guard.

NOTICE: Do not tighten adjusting

screw with clamp lever in open position.

Undetectable damage to guard or

mounting hub may result.

Mounting Guards

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

CAUTION: Guards must be used with

this grinder.

When using the DWE4056, DWE4057, DWE4120,

DWE4156 or the DWE4157 grinder for cutting metal

or masonry, a Type 1 guard MUST be used. Type1

guards are available at extra cost from

DeWALT

distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

see other accessories that can be used with these

grinders.

MOUNTING AND REMOVING (TYPE 27)

ONE-TOUCH GUARD (FIG. 2A)

NOTE: If your grinder is supplied with a keyless

One-Touch guard, ensure the screw, lever, and

spring are fitted correctly before mounting the

guard.

1. Press the guard release lever(J).

2. While holding the guard release lever open,

align the lugs(K) on the guard with the slots (L)

on the gear case.

3. Keeping the guard release lever open, push the

guard down until the lugs engage then rotate

them into the groove on the gear case hub.

Release the guard release lever.

4. With the spindle facing the operator, rotate

the guard clockwise into the desired working

position. The guard body should be positioned

between the spindle and the operator to

provide maximum operator protection.

5. For easy adjustment, the guard can be rotated

in the clockwise direction. NOTE: The guard

release lever should snap into one of the

alignment holes(M) on the guard collar. This

ensures that the guard is secure. The guard

can be repositioned the opposite direction by

depressing the guard release lever.

6. To remove the guard, follow steps 1–3 of these

instructions in reverse.

GUARD WITH FIXING SCREW (FIG. 2B)

1. Place the angle grinder on a table,

spindle(B)up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE4120 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info