Bedienungsanleitung Dik Geurts Instyle 800V (Seite 34 von 112) (Deutsch, Englisch, Holländisch, Französisch)

695347

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

INSTALLATION MANUAL

5.5.2.2 Exempt appliances

Exempt appliances are appliances (ovens, wood burners and stoves) which have been exempted under the Clean

Air Act 1993 or Clean Air (Northern Ireland) Order 1981.

Appliances which are exempt for use in Smoke Control Areas: https://smokecontrol.defra.gov.uk/appliances.php

5.6 Outside air connection (if applicable)

Some fires can be provided with an outside air connection. For an optimum operation of the appliance, the

following should be taken into account in case of an outside air connection:

• The passage of the outside air connection and possibly the passage of a grate may not be smaller than the

passage of the outside air connection on the fire.

• Make sure the maximum underpressure created in the combustion air supply pipe is 4 pascal. If a higher

underpressure is created, the fire will not function properly and (hot) flue gases may flow back into the

supply pipe.

• Prevent placing the outside air supply in an underpressure area on the outside of the house. If possible, place

a supply pipe with T piece to 2 sides of the house.

• The combustion air supply pipe may not be placed higher than the bottom of the fire. This will prevent flue

gases from flowing back.

• The combustion air pipe that is connected to the fire should be made of non combustible material.

• The fire will function properly with a flexible pipe with a maximum length of 11 metres and 4 bends. In case

of a longer pipe or more bends, we recommend placing a pipe with a larger diameter (100-125mm).

• If a crawl space is properly aerated with open grates, it is allowed to retrieve combustion air from there. If

there is no proper aeration in the crawl space, it is possible that harmful radon gases are drawn in. This is not

allowed according to national regulations.

Further information on the outside air connection, if applicable, can be found in section 9 ‘Appliance specific

information’.

Please note that HETAS product approval remains valid for the appliance only when installed with its air supply

taken from the room of installation and the room is ventilated permanently to outside air as necessary in

accordance with the guidelines given in Approved Document J. HETAS product approval is not valid for

appliances fitted with an external air supply ducted directly to the appliance.

5.7 Installing the fire, general

!Caution

• Do not make any changes to the fire yourself.

• Use clean fabric gloves and avoid fingerprints on the fire and flue pipes.

• Depending on the type of suspension, install the fire on a floor, against a wall or on a ceiling with sufficient

load bearing capacity.

• Lay a fire-resistant floor plate if the floor is combustible. The floor plate in non-combustible material must

extend at least 300 mm away from the fire and be at least 300 mm wider than the fire. Check these distances

before installation on the basis of applicable national/local laws.

Tip!

A floor plate offers protection against smouldering ash and prevents the soiling of a marble or flagstone floor, for

example. We therefore also advise using a fire-resistant floor plate when installing appliances on a wall or ceiling.

Use the fire's dimensional sketch to see which fire pipe diameter you need (see Annex 1, table 2).

Use a fire pipe that at least meets the requirements of standards as established in EN 1856-2 T600.

Install the flue pipes in such a way that a fire hazard can never originate.

When installing a free-standing fire take account of the minimum required distance from the fire to a

non-combustible wall. This distance amounts to 50 mm.

When installing the fire and/or flue pipes respect the minimum distance to combustible objects and materials as

shown in Annex 1, table 2.

Take adequate measures to avoid too high temperatures in any walls behind the chimney breast.

This also applies for materials and/or objects behind the wall.

Respect the flue duct requirements as described in paragraph. 5.2.

For any appliance-specific instructions we refer to section 9 'Appliance-specific information'.

!CAUTION

If you are installing a built-in appliance take account of:

• The minimum building-in dimensions according to Annex 1, Table 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Instyle 800V Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Instyle 800V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info