Bedienungsanleitung Dik Geurts Instyle 800V (Seite 36 von 112) (Deutsch, Englisch, Holländisch, Französisch)

695347

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

INSTALLATION MANUAL

Carefully slide the fire into the hole. Make sure that no damage is caused.

If applicable connect the convection opening ( see section 5.3 'Convection') with the flexible aluminium pipe and

ventilation elements (see section 5.4 'Appliances with fan(s))'.

The fire may never support the flue.

Make a good, airtight seal between the fire and the flue, possibly with a register plate and preferably with a fixed

fire pipe or stainless steel double-walled flexible pipe that at least suffices with regard to standard EN 1856-2 T600.

If applicable, and depending on national regulations, the connection between the existing flue duct and the fire

may be plugged with heat-resistant ceramic wool

Proceed as follows:

Check whether the open hearth valve has been removed.

Remove the frame (if the frame is already fitted).

Remove the bottom plates and turn the fire as far as possible downwards with the adjustable legs to make space

for the ceramic wool.

Fill any space behind the fire with fire-resistant insulation material so no dirt can get in.

Remove the flame baffle plate.

Apply the ceramic wool between the top side of the fire and the chimney for an airtight connection.

Turn the fire up again with the adjustable legs and check whether the ceramic wool seals properly.

Replace the flame baffle plate (see section 9 'Appliance-specific information').

!Caution

After the chimney has been swept always check that the connection is still airtight.

A handy kit is available through your supplier for the direct connection of a stainless steel flexible pipe to the fire.

The use of a kit is, however, not required for all appliances (if applicable see section 9 'Appliance-specific

information').

After the fire has been connected turn the adjustable legs with the Allen key supplied until the fire is in the

desired position. Make sure that the combustion air supply is not blocked.

Replace the restrictor cap for the outflow, fit the inner lining plates in reverse order and place the baffle plate

against the back wall and on the profiles (if applicable see section 9 'Appliance-specific information').

Use a torch or a thin screwdriver to check that the secondary ventilation holes in the back wall are directly facing

the recesses in the interior lining.

If applicable replace the frame around the fire (if applicable see section 9 'Appliance-specific information').

5.7.2.2 In a new situation

To install an insert fire with a newly built chimney breast proceed as follows:

Determine the fire location. The dimensions are given in Annex 1, Table 2.

Place the fire on a floor with a sufficient load bearing capacity.

If applicable make a recess for an outside air connection (if applicable see section 9 'Appliance-specific

information').

Use non-combustible and heat-resistant material according to European fire classification A1 EN 13501-1 for the

plate on the floor, chimney breast (including the upper face), the material in the chimney breast and the back wall

against which the appliance is fitted. Plate material or stony materials can be used for this.

Leave a space of at least 10 mm between the fire and construction materials.

Be careful with the chimney breast plaster. Plaster beading makes the recess smaller.

Take account of the expansion of the fire. Keep the fire free of plasterwork.

If there is a combustible ceiling, place a fire-resistant plate with a 10 cm thick heat-insulating layer on top 30 cm

below the ceiling in the chimney breast.

If are there combustible materials (e.g. wooden floor parts/beams etc.) below or behind the fire, sufficient

non-combustible insulation material according to European fire classification A1 EN 13501-1 must be applied.

Comply with national regulations here.

If there is a combustible wall build a 10 cm-thick fire-safe wall.

Build the base or elevation with heat resistant material.

Place the steel plate supplied in the place for the fire. If applicable make a recess in it for the outside air

connection. Remove the fire door and disassemble the frame when it is supplied separately.

Remove the fire door and disassemble the frame when it is supplied separately (see section 9 'Appliance-specific

information').

Install the fire.

If applicable connect the outside air connection (see section 9 'Appliance-specific information').

If applicable connect the convection opening (see section 5.3 'Convection') with the flexible aluminium pipe and

ventilation elements (see section 5.4 'Appliances with fan(s))'.

Keeps these elements at least 30 cm away from the ceiling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Instyle 800V Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Instyle 800V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info