Bedienungsanleitung Dimplex CAS 500R (Seite 12 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

706336

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

This section describes how to activate your re using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the fuel bed. (Fig 21)

CAS500R

Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)

Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate

Button Panel - Controls the functioning of the appliance. (Fig 21B)

• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by a single

beep and the main LED lights activating. Be careful not to look directly into the LED’s as they can be very bright.

Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the

ame effect starts.

• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details.

• is the test mode button. This will be used by the manufacturer and the Service Engineer.

• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep

when you reach the minimum level.

• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible

beep when you reach the maximum level.

• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume

for this is off. You will hear an audible beep when you reach the minimum level

• is the increase re crackling sound. Press this to increase the volume of the crackling sound.You will hear an

audible beep when you reach the maximum level.

CAS1000R

Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)

Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate

Button Panel ‘C’ Controls the functioning of the left side of product while Button Panel ’D’ controls the functioning of the

right side of the product. Please note the ame height and re crackling noise can be controlled independently on each

individual side of the product.

• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by a single

beep and the main LED lights activating. Be careful not to look directly into the LED’s as they can be very bright.

Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the

ame effect starts.

• is the pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details.

• is the test mode button. This will be used by the manufacturer and the Service Engineer.

• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep

when you reach the minimum level

• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible

beep when you reach the maximum level.

• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume

for this is off. You will hear an audible beep when you reach the minimum level.

• is the increase re crackling sound. Press this to increase the volume of the crackling sound. You will hear an

audible beep when you reach the maximum level.

Operating the Product

Multiple Product Installation

Follow steps 1-4 in “Installing the Product into Surround/Enclosure” to t the rst product. It is important that the rst

product is orientated so that the side of the product with the slots is left free and not connected to rst end of the

installation (Fig 18).

1. When the rst product is installed and securely xed, prepare the second product by unscrewing the joining screws

(Fig 19A) and screwing them into the opposite side of the metalwork (Fig 19B). Please note, these screws should

not be fully tightened and 5-10mm of thread should be left protruding from the edge of the product.

2. Fit the second product beside the rst product, ensuring the protruding screws of the second product engage with

slots of the rst product. (Fig 20)

3. Ensure the second product is at the correct height to match the rst product and ensure it is adequately level. This

can be done by adjusting the adjustable feet with a at head screwdriver. (Fig 8) The levelness of the product can

be veried by checking the on-board level (Fig 9)

4. Tighten the screws of the second product so that it joins tightly with the rst product.

Additional products can be tted to the second product by following steps 1-4 above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex CAS 500R Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info