Bedienungsanleitung Dimplex CAS 500R (Seite 13 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

706336

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

RECEIVER CONTROLS

The product can also be controlled using the receiver which is supplied with the product. (Fig 12)

CAS500R

• is the on/standby button. Press it to turn on and off the ame effect.

• is used to mute the re crackling sound. Press this to turn on and off the crackling sound. The volume can be

adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product

restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to

reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.

• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep

when you reach the minimum level.

• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible

beep when you reach the maximum level

CAS1000R

• is the on/standby button. Press it to turn on and off the ame effect.

• is used to mute the re crackling sound. Press this to turn on and off the crackling sound. The volume can be

adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product

restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to

reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.

• is the reduce ame button. Press the reduce ame button on the second button row to reduce the height/intensity

of the ame on the left hand side of the product. Press the reduce ame button on the third button row to reduce

the height/intensity of the ame on the right hand side of the product. You will hear an audible beep when you reach

the minimum level.

• is the increase ame button. Press the increase ame button on the second button row to increase the height/

intensity of the ame on the left hand side of the product. Press the increase ame button on the third button row to

increase the height/intensity of the ame on the right hand side of the product. You will hear an audible beep when

you reach the maximum level.

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control

and after removing the batteries from the plastic wrapping t them into place. Replace the battery cover. With the product

powered off, a functional test can be carried out on the remote control by pushing any button and observing the blue LED

at the top o the remote ashing with each button push.

Pairing the Remote Control

The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by

following the steps below.

1. Press the rocker switch to the on (I) position; a single beep will be heard.

2. Press the button on the Button Panel; the product will turn on.

3. Press the button on the Button Panel, the LED’s will start to slowly blink on and off.

4. Press the button on the remote control; the product LEDs will ash quickly three times and the product will then

automatically switch off. The remote control is now paired to the product and can be used to switch it back on.

The operation of the remote control is the same as described in ‘Receiver Controls’. You can pair multiple products to the

one remote control by repeating the pairing operation as above on your subsequent products. Please note a maximum

of six CAS500R/CAS1000R products can be paired to the one remote control.

Pairing the Remote Control to Multiple Products

If you are installing multiple CAS500R/CAS1000R products you can pair them to a single remote control. To do this,

please install the products as described in the “Installation Instructions”. Ensure that all products are connected to mains

power and have water supplied. If you are pairing CAS1000R and CAS500R products please choose the 6 button

remote control as the master remote control.

1. Pair the rst product as described in steps 1-4 above.

2. On your second product, press the rocker switch to the on (I) position; a single beep will be heard.

3. Press the button on the Button Panel; the product will turn on.

4. Press the button on the Button Panel, the LED’s will start to slowly blink on and off.

5. Press the button on the remote control; the LEDs will ash quickly three times and the product will then

automatically switch off. The remote control is now paired to the two products and can be used to switch them on.

6. Repeat the above steps to pair the next product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex CAS 500R Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info