Bedienungsanleitung Dimplex Edel 200 AIR D-2 (Seite 7 von 24) (Englisch)

798061

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• The oor must be able to support the weight of the heat pump

water heater (weight of the heat pump water heater lled with

water 200 L/ 270 L= 260 kg / 335 kg).

If installed without piping, the appliance must be installed in non-

heated premises (of at least 20m2 and away from neighboring heated

rooms.

•If the space available under the ceiling is less than 60cm in height

above the water heater, it is recommended to install an elbow at the

air outlet and direct it towards the back or the sides.

•The heat pump water heater enables heat to be recovered from

the oor of non-heated, partially underground premises such as a

workshop or garage.

• The heat pump water heater allows the dehumidifying and cooling

of rooms such as utility rooms or cellars.

4.2- Air connection

4.2.1 - Without piping

Partial piping

Exterior air Heated room

The heat pump can operate over a large air temperature range (from

-7°C to +35°C). The appliance extracts calories from exterior air. Partial

piping (using only 1 pipe) onto exterior air should be avoided as in

the winter it can cause the room to become signicantly colder.

4.2.2 - With piping

piping at the back piping on the right piping on the left

The heat pump water heater must be connected using

insulated air ducts with an interior diameter of 160mm.

90° Ø160 mm PVC elbows allow you to rotate the position of the

pipes connected to the appliance through 360o.

Total maximum length Ø160 :

• 6 m of exible hose

• 12 m of semi rigid piping

1 elbow= 1m

Rep. Description

Semi-rigid pipe Ø160mm - lg 2m

Insulated 90° elbow Ø160mm

Collars for attaching to wall (set of 2)

Connectors for insulated pipes (set

of 2)

Horizontal terminal for insulated pipe







Piping accessories are available to order and are designed for a

simple and ecient heat pump water heater connection.

The pipes (Ref. 730011) and the foam elbows  (Ref. 730012), are

semi-rigid, light and thermally insulated.

They are assembled using an assembly connector. (Ref.730014).

If over 1m long, the pipes must be anchored to the wall using a collar.

(Ref. 730013).

The stainless steel horizontal terminal (Ref. 730015), is equipped

with a protective grill.

4.2.3- Piping accessories

4.3 - Hydraulic connections

• A new pressure-relief valve (not included) must be installed and

set to 6 bars on the domestic cold water supply of the appliance.

We would recommend a membrane valve.

The membrane valve system must conform to national and

domestic standards and regulations in eect.

• The pressure-relief valve should be installed as close as possible

to the appliance’s cold water inlet and the water ow should

never be hampered by any accessory (valve, pressure-

reducer, etc...)

• The pressure-relief valve drainage outlet must be installed in a

frost-free place, in a downward-sloping position.

• The pressure-relief valve drainage outlet should be sized

according to building regulations and must never be obstructed.

It should be connected to a vertical draining pipe, using a funnel

which allows an open space of at least 20mm and which is at

least equal in diameter to the appliance’s piping connection.

• If the pressure of the domestic cold water supply is higher than 5

bars, a pressure-reducer should be installed above the pressure-

relief valve near the starting point of the installation (a pressure

of 4-5 bars is recommended).

• It is advised to t a shut-o valve above the pressure-relief valve.

• For installations equipped with:

- piping of a small diameter

- ceramic plate valves

A domestic water expansion vessel, or anti-hammer valves

which are adapted to the installation should be installed as close

as possible to the shut-o valve.

• The following materials should be used for the

The vertical position of the heat pump

water heater must be strictly respected.

If not, there is a risk of condensates

leaking and resulting in a water leak at

the base of the appliance.

• Use the anchoring point at the bottom of the tank to x the

appliance to the oor, using the metal tab (pre-assembled under

the foot) and an ØM8 screw which can be then dowelled into

the ground (see Rep.).

- INSTALLER HEAT PUMP WATER HEATER 200 -270L AIR D/2 - MANUAL - 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Edel 200 AIR D-2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex Edel 200 AIR D-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info