Bedienungsanleitung Dimplex Edel 200 AIR D-2 (Seite 14 von 24) (Englisch)

798061

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5.9.2.2 - fan mode

Enter

Select the mode

fan mode

5.9.2.3 - T°C. MINI Minimum temperature

The electrical back-up can be activated at the same time as the

heat pump to prevent the water temperature from going below

a minimum comfort level of 38oC. The electrical back-up will start

up and raise the water temperature to 43oC, and then it will switch

o and the heat pump will complete the heating cycle.

• Press to return to the main menu.

• This function is deactivated by default.

5.9.2.4 - Load shedding -Level authorised

during peak hours

5.9.2.5 - max time Max heating time

Enter

Select mode

T°C. MINI

yes

Enter

Select the mode

shedding

When load shedding is activated you can choose to prevent

certain elements from running (Electrical resistance and

compressor).

• Press to return to the main menu.

If load shedding is switched on:

Mode 0 = No element is allowed to operate

Mode 1 = Only the heat pump is allowed to operate

Mode 2 = The heat pump and back-up are allowed to operate

(neutralising the «peak hours» function)

If the PV function is activated, load shedding cannot be done

through the peak/o-peak hours dry contact. In this case the

timer must be programmed (see § «Programming»).

It is possible to select the length of the desired heating time. The

heat pump water heater can automatically use the electrical back-

up at the same time as the heat pump to speed up the heating

time of the tank.

If you choose MAX time = AUTO, the heating time is limited to a

maximum of 5h during o-peak hours.

• In case of load shedding the «T°C mini» function is not activated.

Factory setting= 1

Mode 1 = Standard mode, automatic ventilation

Mode 2 = Forced ventilation, max speed

Mode 3* = Ventilation activated during water heating periods

and ventilation regulated by an external control

(such as a moisture sensor)

The external control should be connected to connector 2 on the

electronics board in the heat pump water heater. (See appendix

for electrical diagram)

*If PV mode is activated, controlled ventilation (fan moDE 3) is not

available.

• Press to return to the main menu.

Enter

Select time period

between 1 and 24 hours

max time

• This function is deactivated by default.

• Press to return to the main menu.

5.9.3 -Locking the keyboard

Enter

Select locking level

locking

Permanent and automatic locking

The «locking» menu enables you to create three possible levels of

locking for accessing the menus.

In the «Installer» menu turn the dial to «locking.».

NO = Locking is not activated, but manual

locking is possible by pressing

for 3 seconds.

• If a cycle is interrupted by a period where the back-up is not

allowed to run (electricity provider signal or programmed time

slots) it will relaunch during the next authorised period.

•No anti-legionellosis cycle except when returning from holidays

and after a frost protection period of more than 3 days.

•During the anti-legionellosis cycle the temperature is raised

between 55°C and 70°C.

- INSTALLER HEAT PUMP WATER HEATER 200 -270L AIR D/2 - MANUAL-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Edel 200 AIR D-2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex Edel 200 AIR D-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info