Bedienungsanleitung Dimplex Firebox DF 2608 Opti-flame (Seite 5 von 35) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

706559

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Controls: See Fig. 3

Icon Display Function Description

A -

Power /

Standby

Press once to turn the product ‘ON’.

Press a second time to put the product into ‘STANDBY’

(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product

has been plugged out, in which case it will reset to factory settings)

Sleep

Timer

Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning

off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)

Flame Effect

‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,

DEMO MODE and OFF.

Low

Flame

This setting will run the ame effect at a low brightness level. (The display will show F1)

High

Flame

This setting will run the ame effect at a high brightness level. (The display will show F2)

Demo

Mode

This setting will slowly pulse the ame effect between low and high brightness. (The display will show

FP)

- Off

This will turn the ame effect off. If the heater is running, the display will activate and remain active to

read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.

Log Effect

‘LOG EFFECT’ button cycles the unit sequentially through the 3 setting, ‘PULSING LOGS, STATIC LOGS

and OFF.

Pulsing

Logs

This setting will make the logs pulse. (The display will show FP)

Static

Logs

This setting will make the logs stay lit. (The display will show FS)

- Off This setting will turn the logs off.

E - On / Off

This button cycles the top light ‘On’ and ‘Off’.

Heat

‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW

and OFF. The heat setting will be indicated by an icon in the oating display see Fig.1.

When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however if the heater is

being used independently of the ame effect. The low heat or high heat icon will appear continuously

in the oating display.

Low Heat

This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon

and the letters ‘LO’ appearing in the display.

(This icon is Orange in Colour)

High

Heat

This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’

icon and the letters ‘HI’ appearing in the display.

(This icon is Red in Colour)

Cool

Blow

This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL

BLOW’ icon and the letters ‘CB’ appearing in the display.

(This icon is Blue in Colour)

- Off

This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display. Note the

blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.

G -

Temp

Down

Press multiple times to lower the heater temperature in 1°C increments. The lowest temperature that

can be set 5°C.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

H - Temp Up

Press multiple times to increase the heater temperature in 1°C increments. The highest temperature

that can be set 37°C.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

User Modes:

Mode Name /Description Action (Actions cannot be input by remote control)

Change Celsius (° C) to Fahrenheit (° F)

Press both 3 Dot Button ( ) and 2 Dot ( ) on the unit and hold until beep is heard

and display flashes. (To revert back to Celsius repeat this action)

Disable/Enable Heat Options

Hold both 1 Dot Button ( ) and Flame Button ( ), on the unit, for 2 seconds, when

the heater has been disabled the display will read “--” and beep. To enable heat

repeat this action.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Firebox DF 2608 Opti-flame Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info