Bedienungsanleitung Dimplex Juneau (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch)

706557

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Control Knob ‘C’:- Controls the intensity of the ame effect.

Turning the control knob clockwise increases the ame effect, turning the control knob anti-clockwise will

decrease the ame effect.

When the water tank is empty the main lamps go out. See instructions under ‘Maintenance’, ‘Filling the water tank’.

When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the ames return.

Remote Control Operation

On the control panel, Switch A (see Fig.2) must be in the ‘ON’ ( I ) position in order for the remote control to operate.

There are 3 buttons on the remote control. (See Fig.7)

To operate correctly the remote must be pointed towards the front fuel effect.

The remote control functions are as follows:

Press once to turn on Flame effect only.

This will be indicated by one beep.

Standby

This will be indicated by one beep.

Battery Information.

1. Unclip the battery cover on the back of the remote control. (See Fig.7)

2. Install AAA batteries into the remote control.

3. Replace the battery cover.

Discard leaky batteries.

Dispose of batteries in the proper manner according to provincial and local regulations.

Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are

not replaced at the same time, if disposed of in a re, or if an attempt is made to charge a battery not intended to be

recharged.

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen

if the heat outlet is restricted in any way. If the cut-out operates, unplug the re from the socket outlet and allow

approximately 10 minutes before reconnecting. Before switching the re back on remove any obstruction that may be

restricting the heat outlet, then continue normal operation.

Tips for using your appliance.

1. Only pull out the drawer when its time to rell the water tank or change a lamp, otherwise it may lead to excess

water in the sump and reduced ame effect. If this happens empty the water from the sump as instructed under

‘Maintenance’.

2. With the ame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as

long than when it is at maximum ame setting.

3. Do not tilt or move the re while there is water in the tank or sump.

4. Make sure that the re is on a level oor.

5. The ame control knob ‘C’ (Fig.2) may be turned up or down to give a more realistic effect.

6. Sometimes the ames appear more real when the ame control knob is turned down.

7. Give the ame generator some time to react to changes you may make on the ame control knob.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE

Fitting Replacement Lamps.

If a large amount of the smoke appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the ame effect on, open the drawers fully, gently pull the drawer fully out by the tab. (See Fig.3)

2. View the lamps from a distance in front of the re and observe which lamp needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the re from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the water tank by lifting upwards and place in a sink.

6. Remove the sump as described in the Cleaning Section.

7. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (See Fig. 4

and 5). Replace with an Opti-myst, 12V, 45W, Gu5.3 base, 8° beam angle, coloured lamp.

8. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push rmly in place. (See Fig.4

and 5).

9. Replace the sump and water tank and carefully close the drawer.

10. Switch on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Juneau Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info