Bedienungsanleitung Dimplex Juneau (Seite 10 von 36) (Deutsch, Englisch, Holländisch, Französisch)

706557

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Filling the water tank.

When the water tank is empty, ame and smoke effect shuts off, and you will hear 2 audible ‘beeps’. Follow these

steps to rell:

1. Press Switch ‘A’ to (0). (See Fig.2)

2. Pull out the drawer as far as possible by the tab. (See Fig.3)

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig.6)

5. Fill tank with ltered tap water. This is necessary to prolong the life of the ame and smoke producing unit. Do not

use a decalcier.

6. Screw the cap back on, do not overtighten.

7. Return the tank to the sump, with the tank cap facing down and the at side of the tank facing outward.

8. Press Switch ‘B’ once to turn on ame effect. (See manual control section and Fig.2).

9. Press Switch ‘A’ to ‘ON’ ( I ) position. (See Fig.2)

10. Gently push the drawer back in as far as it will go.

Cleaning.

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE FIRE.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air lter.

For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or

uff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan re.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in

the outer groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, ret the cap and shake well, rinse out until all traces of

washing up liquid are gone.

4. Rell with tap water with a maximum hardness of 10 dH only, replace the cap, do not overtighten.

5. Do not use a decalcier when cleaning the appliance, this may shorten the lifetime of the smoke unit.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position

2. Gently pull the drawer out as far as possible. (See Fig.3)

3. Remove the water tank by lifting upwards.

4. Disconnect the electrical connector, located on the left side of the sump, by rst loosening the two retaining screws

and gently withdrawing the connector. (See Fig.8)

5. Release the lower sump locking tabs by turning 90º, this allows the sump to be lifted completely from its location.

(See Fig.9)

6. Gently lift up the sump assembly, taking care to keep level so as not to spill any water. Sit the assembly in the sink.

(See Fig.10)

7. Release the two upper sump locking tabs by turning 90º, then lift off the sump lid. (See Fig.11)

8. Carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig.12)

9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces

including the metal disc and the rubber seal located in the top grooved surface. Do not remove the rubber seals.

(See Fig.13 and 14)

10. When cleaned, thoroughly rinse the sump with clean water.

11. Clean the outlet surface of the sump lid with the brush and ush out thoroughly with water. (See Fig.15 & 16)12.

Reverse the above steps to reassemble.

Air lter.

1. Gently pull the drawer out as far as possible. (See Fig.3).

2. Press Switch ‘A’ to the ‘OFF’ (0) position (See Fig.2)

3. Remove the tank and place in a sink with the cap facing upwards.

4. Gently slide upwards the air lter plastic holder. (See Fig.17)

5. Remove the lter combination from the plastic holder.

6. Gently rinse with water in the sink and dry with fabric towel before returning.

7. Replace the lter combination making sure that the course black lter is in contact with the plastic holder. (See

Fig.18)

8. Replace the tank.

9. Press Switch ‘A’ to the ‘ON’ ( I ) position (See Fig.2).

10. Close the drawer fully.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Juneau Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info