Bedienungsanleitung Dimplex Moorefield (Seite 22 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

706516

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

Operating the Fire

This section describes how to activate your re using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the hinged ap. (Fig.10 for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate either with or without heat.

Switch ‘B’:- Press

once to turn on the ame effect. This will be indicated by an audible beep. Although the main lights

operate immediately it will take a further 30 seconds before the ame effect starts.

Press

again to give ame effect and half heat. This will be indicated by two beeps.

Press

again to give ame effect and full heat. This will be indicated by three beeps.

Press

again to return to ame effect only. This will be indicated by one beep.

Press to put re in to standby mode. This will be indicated by one beep.

Control Knob ‘C’:- Controls the Thermostat setting.

Turning the control knob to the left will decrease the temperature setting, turning the control knob

to the right will increase the temperature setting.

Control Knob ‘D’:- Controls the intensity of the ame effect.

Turning the control knob to the left increases the ame effect, turning the control knob to the right will

decrease the ame effect.

SETTING THE THERMOSTAT

Ensure the re is plugged in and switch it on to the full heat setting. Turn the Control Knob ‘C’ fully to the right (max

temperature setting) to warm the room rapidly. When the room temperature has reached the desired level, turn

the thermostat knob back slowly until you hear the thermostat just click off. The heater will then maintain the room

temperature at the chosen level.

Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room temperature

being higher then the thermostat setting

THERMAL SAFETY CUT-OUT

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if

the heat outlet was restricted in any way. If the cut-out operates, unplug the heater from the socket outlet and allow

approximately 10 minutes before reconnecting. Before switching the heater back on remove any obstruction that may

be restricting the heat outlet, then continue normal operation.

Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be

supplied through an external switching device, such as a timer, or connected to a switch that is regularly switched on

and off by the utility.

GETTING THE DESIRED FLAME EFFECT

1. The ame control knob ‘D’ (Fig.10) may be turned up or down to give a more realistic effect.

2. Generally the ames appear more realistic when the ame control is turned down.

2. Lift out the Sump Nozzle (Fig 3)

3. Insert lamps into lamp holders (Fig 4), carefully locating the pins into the holes (Fig 4a)

4. Push lamps rmly into place

5. Place the Transducer Unit into the sump and join the cable to the connector on the sump (Fig 5)

6. To ensure that the Transducer Unit is correctly placed in the sump, the tab on the Transducer Unit should be lined

up with the moulded recess in the sump (Fig 5a).

7. Ensure that the cable is not placed above the disc on the Transducer Unit (Fig 5b). To prevent the cable becoming

pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump.

8. Replace the Sump Nozzle and secure it by turning the two red tabs by 90 degrees (Fig 6)

Filling the Water Tank

9. Place Water Tank in sink and remove cap (turn anti-clockwise to open) (Fig 7)

10. Fill Water Tank with decalcied tap water only. This is necessary to prolong the life of the ame and smoke

producing unit. The water should be ltered through a conventional domestic water lter unit and the lter should

be replaced regularly.

11. Screw the cap back on – do not overtighten.

12. Place the Water Tank in the Sump, with the tank cap facing down and the at side of the tank facing outward (Fig 8)

Assembling the re

13. Place the Fuelbed on top of the Water Tank and Mist Nozzle (Fig 9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Moorefield Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex Moorefield

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info