Bedienungsanleitung Dimplex Wickson (Seite 7 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Norwegisch)

706539

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Controls: See Fig. 2 & 3

Icon Display Function Description

A -

Power /

Standby

Press once to turn the product ‘ON’.

Press a second time to put the product into ‘STANDBY’

(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product

has been plugged out, in which case it will reset to factory settings)

Sleep

Timer

Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning

off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)

Flame Effect

‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,

DEMO MODE and OFF.

Low

Flame

This setting will run the ame effect at a low brighness level. (The display will show F1)

High

Flame

This setting will run the ame effect at a high brighness level. (The display will show F2)

Demo

Mode

This setting will slowly pulse the ame effect between low and high brightness. (The display will show

FP)

Off

This will turn the ame effect off. If the heater is running, the display will activate and remain active to

read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.

Colour Theme ‘Colour Themes’ are setting which change the colour of the fuel bed there are eight different themes

Theme 1

Theme 1 is a ‘Demo Mode’ this setting will scroll throught all of the colour settings you can ‘Pause’

this demo mode by pressing the ‘Brightness Button’ / in which case the display will read

1.p

‘Unpause’ press the ‘Brightness Button’ / in which case display will read

1.U

2-8

Theme

2-8

Themes 2-8 are preset colours that remain static.

Bright-

ness

This button switches themes 2-8 between full brightness and half brightness. This button also interacts

with the product when set on theme as perviously described above

Heat

‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW

and OFF. The heat setting will be indicated by an icon in the oating display see Fig. 2.

When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however if the heater is

being used independantly of the ame effect. The low heat or high heat icon will appear continuously

in the oating display.

Low Heat

This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon

and the letters ‘LO’ appearing in the display.

(This icon is Orange in Colour)

High

Heat

This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’

icon and the letters ‘HI’ appearing in the display.

(This icon is Red in Colour)

Cool

Blow

This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL

BLOW’ icon and the letters ‘CB’ appearing in the display.

(This icon is Blue in Colour)

- Off

This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display. Note the

blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.

G -

Temp

Down

Press multiple times to lower the heater temperature in 1ºC increments. The lowest temperature that

can be set 5ºC.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

H - Temp Up

Press multiple times to increase the heater temperature in 1ºC increments. The highest temperature

that can be set is 37ºC.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

User Modes:

Mode Name /Discription Action (Actions cannot be input by remote control)

Change Celsius (º C) to Fahrenheit (º F)

Press both 3 Dot Button ( ) and 2 Dot ( ) on the unit and hold until beep is heard

and display flashes. (To revert back to Celsius repeat this action)

Disable/Enable Heat Options

Hold both 1 Dot Button ( ) and Flame Button ( ), on the unit, for 2 seconds, when

the heater has been disabled the display will read “--” and beep. To enble heat repeat

this action.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Wickson Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info