Bedienungsanleitung Dirt Devil M 5080 - EQU Turbo Silence (Seite 18 von 30) (Deutsch, Englisch, Französisch)

500166

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

6 Troubleshooting

6.1 Before you send in the appliance

Before contacting your authorised Royal dealer, Royal service partner or

appliance market or sending in the appliance, first follow the procedure in

the following table to check if you can solve the problem yourself.

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing Chapter 4.3, "Switching off".

No. Problem Possible cause Solution

1 The cleaning results are

not satisfactory although

the cleaning indicator

(Fig. 1/8) is green.

The bypass vent (Fig. 1/19) is open. Close the bypass vent (Fig. 1/19).

The attached nozzle is unsuitable. Change the nozzle, Chapter 3.2, "Selecting the proper nozzle".

The position of the ‘carpet/hard floor’

selector (Fig. 1/2) is unsuitable.

Set the "carpet/hard floor" selector (Fig. 1/2) to the correct position for the

type of floor, Chapter 4.2, "Vacuum cleaning", step 4.

The dust container is full. Empty the dust container, Chapter 5.1, "Emptying the dust container".

Nozzle, telescopic tube or suction

hose is blocked.

Remove the obstacle. If necessary, use a long wooden stick (e.g. a broom-

stick) to do this.

2 The cleaning indicator

(Fig. 1/8) suddenly begins

to slowly flash red during

cleaning.

The dust container has not been

emptied often enough, or the nozzle,

telescopic tube, or suction hose is

blocked.

1. Switch off the appliance and pull the plug from the mains socket,

Chapter 4.3, "Switching off".

2. Empty the dust container, Chapter 5.1, "Emptying the dust container".

3. Replace the dust container.

4. Plug the plug into a socket and turn the clean and fully-assembled vacu-

um cleaner back on.

5. If the cleaning indicator (Fig. 1/8) flashes red for more than thirty seconds

after being switched back on despite the dust container being empty, then

you also have to clean the components of the vacuum cleaner, Chapter

5.2, "Cleaning the dust container and cyclone unit" and Chapter 5.3,

"Cleaning the dual motor protection filter".

6. Take this opportunity to remove the nozzle, telescopic tube, or suction

hose from the appliance and remove any blockages (e.g. with a broom

stick).

7. Plug the plug into a socket and turn the clean and fully-assembled vacu-

um cleaner back on. The cleaning indicator (Fig. 5/5) will continue to flash

red slowly for 20–30 seconds (self-analysis mode) and will then change

to green (operational).

3 The cleaning indicator

(Fig. 1/8) slowly flashes

red for 20–30 seconds af-

ter being switched back

on.

This is normal. Your vacuum cleaner

performs a self-analysis during this

time.

After 20–30 seconds the cleaning indicator (Fig. 1/8) turns back to green.

4 The cleaning indicator

(Fig. 1/8) slowly flashes

red for longer than 30 sec-

onds after being switched

back on.

The cleaning carried out was not suf-

ficient.

Proceed in accordance with the solution for problem no. 2.

5 The cleaning indicator

(Fig. 1/8) flashes red fast

after flashing red slowly

for a while during clean-

ing.

The dust container has not been

emptied often enough, or the nozzle,

telescopic tube, or suction hose is

blocked. If you do not react soon, the

integrated protective mechanism in

the vacuum cleaner will turn the ap-

pliance off automatically before it

overheats.

Proceed in accordance with the solution for problem no. 2.

6 The appliance suddenly

stops vacuuming and the

cleaning indicator (Fig. 1/

8) continues to flash red

fast.

The protective function in the vacu-

um cleaner, which turns the appli-

ance off before it overheats, has

been triggered because you contin-

ued to vacuum even though the

cleaning indicator was flashing red,

meaning there was a risk of over-

heating.

Proceed in accordance with the solution for problem no. 2.

NOTE:

If you cannot solve the problem following these instructions, contact our customer services (contact Page 60, "International Service").

M5080.book Seite 18 Dienstag, 24. April 2012 10:48 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M 5080 - EQU Turbo Silence Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info