Bedienungsanleitung Dirt Devil M2827-2 Centec (Seite 9 von 38) (Deutsch, Englisch, Dänisch, Schwedisch, Finnisch)

571436

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

5 Maintenance

5.3 Cleaning the exhaust filter

1. Switch off the appliance, Zchapter 4.3, „Switching off“.

2. Push the release catches of the exhaust filter cover down (Fig. 13/A)

and fold down the exhaust filter cover.

3. Remove the exhaust filter (Fig. 13/B).

4. Hold the exhaust filter deeply into a dustbin.

5. Only now separate the exhaust filter element from the filter holder

(Fig. 14/A).

6. Thoroughly tap the dirt from both elements.

7. Remove residual dust with a soft brush, e.g. the supplied furniture

brush.

8. If the exhaust filter element is damaged, deformed or too soiled,

replace it (ordering information Zchapter 5.4, „Spare parts and

accessories“).

9. Put the cleaned or new exhaust filter element back into the filter holder.

10. Now put the filter holder with the freshly fitted filter back into its

receptacle (Fig. 13/B).

11. Fit the exhaust filter cover on the bottom side first (Fig. 14/B) and then

fold it in upwards.

5.4 Spare parts and accessories

 Ordering address: ZPage 37, „International Service“

 Further information: Z www.dirtdevil.de

 The following accessories and spare parts can be reordered:

5.5 Before you send in the appliance

Before contacting your authorised Royal dealer, Royal service partner or

appliance market or sending in the appliance, first follow the procedure in

the following table to check if you can solve the problem yourself.

A B

ATTENTION:

The exhaust filter element is not washable.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have acquired by reordering.

Item number Description

2827001 Filter set 4 pcs, consisting of 1 central lamellae filter,

1 filter screen, 1 motor protection filter, 1 exhaust filter

M203 1 parquet brush

M209 1 turbo brush

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing Zchapter 4.3, „Switching off“.

Problem Possible cause / solution

The appli-

ance will not

start.

The socket does not carry current.Test the vacuum clean-

er at another socket which you are sure carries current.

Power cord is damaged. Have the power cord replaced by

Royal Appliance Customer Service, address, ZPage 37,

„International Service“.

The vacuum

cleaner

stops sud-

denly.

The overheating protection has tripped (possibly due to

blocked suction channels, filters, or similar).

Switch the appliance off and pull the plug out of the socket.

Remove the cause of overheating (e.g. by disassembling

telescopic tube and suction hose and removing the obsta-

cle and/or cleaning filters). Wait for about 45 minutes. After

the appliance has cooled off, you may switch it on again.

Cleaning in-

dicator

(Fig. 1/24)

lights up.

The central lamellae filter is dirty. Clean the central lamel-

lae filter, Zchapter 5.2, „Cleaning central lamellae filter

and motor protection filter“.

The dust container is full.

Empty / clean the dust container, Zchapter 5.1, „Emptying

and cleaning the dust container“.

The clean-

ing results

are unsatis-

factory in

spite of the

appliance

working cor-

rectly.

The bypass vent (Fig. 1/9) is open.

Close the bypass vent .

The attached nozzle is unsuitable. Change the nozzle,

Zchapter 3.2, „Selecting the proper nozzle“.

The suction power you set is unsuitable.

Adjust the suction power control to suit the flooring,

Zchapter 4.2, „Vacuum cleaning“, step 4.

The position of the "carpet/hard floor" selector (Fig. 1/5) is

unsuitable. Set the "carpet/hard floor" selector to the cor-

rect position for the type of floor, Zchapter 4.2, „Vacuum

cleaning“, step 5.

The dust container is full.

Empty / clean the dust container Zchapter 5.1, „Emptying

and cleaning the dust container“.

The filter is dirty.

Clean the respective filter Zchapter 5.2, „Cleaning central

lamellae filter and motor protection filter“ or Zchapter 5.3,

„Cleaning the exhaust filter“.

Nozzle, telescopic tube or suction hose are blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

NOTE:

If you cannot solve the problem following these instructions, contact the

Royal Appliance customer service (ZPage 37, „International Service“).

Problem Possible cause / solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M2827-2 Centec Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dirt Devil M2827-2 Centec

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info