749187
13
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
13 BOX - IP1529
GB
supplied (see RELEASE INSTRUCTIONS), drill a hole of Ø13
in the up and over door in line with the release pin [B].
3.3 Installingtheleft-handgearmotor
In the event of left-hand side assembly, it is necessary to rotate
the gearmotor 180° so that the release shaft is pointing towards
the centre of the up and over door.
Follow the indications as shown in g.10.
- Disassemble the snap ring, unthread the lever and
disassemble the upper bracket.
- Rotate the gearmotor 180°.
- Thread the lever (also rotated 180°) back on, then fasten
the snap ring back on and reassemble the upper bracket.
3.4 Installingthelimitswitch
It is possible to install the BOXFC1 limit switch as shown in the
gures.
4. ELECTRICAL CONNECTIONS
The BOX30 and BOX40 gearmotors can be connected to the
E1BOX control panel.
Note: if using the E1BOX control panel:
- remove the bottom casing [4],
- x the control panel [10] to the base plate [7].
The gearmotor BOX3SH can be connected to the VIVAH control
panel.
The gearmotor BOX3EH can be connected to the E1HBOX
control panel.
The electrical wiring and the start-up of the gearmotors BOX30,
BOX40 and BOX3SH are shown in g.12 -13 and in the instal-
lation manuals of the control panels E1 and VIVAH.
The electrical wiring and the start-up of the gearmotor BOX3EH
are shown in the installation manual of the control panel
E1HBOX.
5. MAINTENANCEPROGRAM(every6months)
Without 230 V~ power supply and batteries if present:
- Clean and lubricate the moving parts, using neutral grease.
- Check the stability of the automatic system and make sure
that all screws are correctly tightened.
- Check the value of the capacity of the motor condenser.
Reconnect the 230 V~ power supply and batteries if present:
- Check the power adjustment.
- Check that all commands and safety functions (photocells)
are operating correctly.
- Check the batteries are working (continuously) if present,
along with the VIVAH control panel, by removing the power
supply and making a series of operations. Once performed,
turn on the 230 V~ power supply again.
WARNING: For spare parts, see the spares price list.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DITEC BOX30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info