Bedienungsanleitung Dolmar 111 (Seite 17 von 28) (Englisch)

507648

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- Remove the Þ lter cover and air Þ lter (see "Cleaning the

air Þ lter").

- To enable hot-air induction from the cylinder, remove the

plug (A/1) using the universal wrench.

NOTE:

Keep the plug in the saw’s tool kit. You must put the plug back

in at temperatures above 0° C / 32° F.

- Reinstall the air Þ lter and Þ lter cover.

- The snow Þ lter (B/1, see “Accessories”) prevents the induc-

tion of powder snow. It is placed under the preÞ lter (B/2).

NOTE:

Remove the snow Þ lter before working at temperatures above

0° C (32° F)!

When not in use, store the snow Þ lter in the assembly tool

pouch.

Handle heating

(electric, special equipment for model 110i H and 115i H)

The electrically heated handles are activated by pushing the

switch (B/3).

Switch up - ON

Switch down - OFF

The chain needs sharpening when:

- The sawdust produced when sawing damp wood looks

like wood ß our.

- The chain penetrates the wood only under great pressure.

- The cutting edge is visibly damaged.

- The saw is pulled to the left or right when sawing. This is

caused by uneven sharpening of the chain.

Important: Sharpen frequently, but without removing too

much metal!

Generally, 2 or 3 strokes of the Þ le will be enough.

Have the chain resharpened at a service centre when you

have already sharpened it yourself several times.

Proper sharpening:

CAUTION:

Use only chains and guide bars designed for this saw (see

the Extract from the spare-parts list)!

- All cutters must be of the same length (dimension a). Cutters

with different lengths result in rough running of the chain and

can cause cracks in the chain.

- The minimum cutter length: 0.11" (3 mm). Do not resharpen

the chain when the minimum cutter length has been reached;

at this point, the chain must be replaced (see the Extract

from the spare-parts list and "Replacing the saw chain").

- The depth of the cut is determined by the difference in height

between the depth limiter (round nose) and the cutting

edge.

- The best results are obtained with a depth-limiter depth of

.025" (0.64 mm).

CAUTION:

Excessive depth increases

the risk of kickback!

MAINTENANCE

Sharpening the saw chain

CAUTION:

Before doing any work on the guide bar or chain, always

switch off the engine and pull the plug cap off the spark

plug (see "Replacing the spark plug"). Always wear protec-

tive gloves!

.025"

(0,64 mm)

.025"

(0,64 mm)

Working in winter

In order to prevent carburetor icing in conditions of low tem-

perature combined with high humidity, and in order to get up

to operating temperature faster in subfreezing temperatures,

heated air can be taken from the cylinder.

At temperatures above freezing the carburetor must NOT be

fed heated air.

Failure to follow these instructions can lead to damage

to the cylinder and piston!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar 111 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dolmar 111

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info