Bedienungsanleitung Dolmar AR-3733 (Seite 11 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598403

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

11ENGLISH

►Fig.2: 1. Red indicator 2. Button 3. Battery

cartridge 4. Battery holder

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

NOTE:Thetooldoesnotworkwithonlyonebattery

cartridge.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotection

system.Thissystemautomaticallycutsoffpowerto

themotortoextendtoolandbatterylife.Thetoolwill

automaticallystopduringoperationifthetoolorbattery

isplacedunderoneofthefollowingconditions.Insome

conditions, the lamps on the switch box lights up.

Overload protection

Whenthetoolisoperatedinamannerthatcausesitto

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the

tooloffandstoptheapplicationthatcausedthetoolto

becomeoverloaded.Thenturnthetoolontorestart.

Overheat protection

Whenthetoolisoverheated,thetoolstopsautomati-

cally, and the green lamp on the switch box blinks. In

thissituation,letthetoolcooldownbeforeturningthe

tool on again.

Overdischarge protection

Whenthebatterycapacitybecomeslow,thetoolstops

automatically. And the red lamp on the switch box lights

uporblinks.Iftheproductdoesnotoperateevenwhen

theswitchesareoperated,removethebatteriesfrom

the battery holder and charge the batteries.

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►Fig.3: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforfewseconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Switch action

CAUTION: Before connecting the battery to

the shears, always check to see that the switch

trigger actuates properly and returns to the “OFF”

position when released.

CAUTION: When not operating the tool,

always make sure that the I/O switch is on the "O"

side.

CAUTION:

Do not press the I/O switch to the

“I" (on) position while pulling the switch trigger.The

bladeclosesslightlyanditmaycausepersonalinjury.

Toturnonthetool,performasfollows:

1. Connect the switch box, connection cord, and

shears.(Referto“Installingtheconnectioncord”.)

2. Holdtheshearsrmly,andpresstheI/Oswitchto

the“I"(on)position.Thegreenpilotlamplightsup.

►Fig.4: 1.I/Oswitch 2.Pilotlamp(green) 

3. Pilot lamp (red)

3. Theshearbladesarelocked-modewhentheI/O

switchison.Toreleasethelock,pulltheswitchtrigger

twotimes.Theuppershearbladeopensautomatically.

4. Toclosetheshearblade,pulltheswitchtrigger.

►Fig.5: 1. Switch trigger

Auto locked-mode and shut-off

mode shift

Forsafetyreasons,thetoolshiftsintolocked-modeor

shut-offmodeautomaticallyifthetoolisleftuntouched

foracertainperiodoftime.

After5minutes:Thetoolshiftsintolocked-mode.Pull

the switch trigger two times to release the lock.

After15minutes:Thetoolisshiftintoshut-offmode,

andthegreenpilotlampturnsoff.PresstheI/Oswitch

tothe“O"(off)positiononce,andpresstheI/Oswitch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar AR-3733 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info