Bedienungsanleitung Dolmar AR-3733 (Seite 12 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598403

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

12 ENGLISH

tothe“I"(on)positionagain,thenpulltheswitchtrigger

two times to release the lock.

Opening angle selector lever

►Fig.6: 1. Opening angle selector lever

Bytiltingtheopeningangleselectorlevertotheleft

side, you can open the upper shear blade wider.

Tolimittheuppershearbladeopeningangle,rstpull

theswitchtriggerfully,andthenreturntheopening

angle selector lever to straight position.

Cutting depth adjustment

CAUTION: Do not let your hands or part of

body close to the shear blades. Otherwise per-

sonal injury may result.

Aftersharpeningorreplacingtheshearblade,adjust

cuttingdepthifnecessary.

Turnonthetool,andpulltheswitchtriggertwotimesto

opentheshearblades,andthenpresstheI/Oswitchto

the“O"(off)position.

Todeepenthecuttingdepth,turnthecuttingdepth

adjustingscrewclockwisewiththehexwrench.Andto

make the cutting depth shallower, turn the cutting depth

adjustingscrewcounterclockwise.

►Fig.7: 1.Cuttingdepthadjustingscrew

NOTE:Checkthecuttingdepthafteradjustment.If

the cutting depth is too shallow, the branch may not

cutfully.

Pilot lamps on the switch box

►Fig.8: 1.I/Oswitch 2.Pilotlamp(green) 

3. Pilot lamp (red)

Thegreenandredlampsindicateasfollows:

(On:

Off: Blinking: )

• Greenlamplightsup:thetoolisturnedon.

Green Red

• Greenlampblinks:thetoolisoverheated.Letthe

toolcooldownbeforeturningthetoolonagain.

Green Red

• Greenlamplightsupandredlampblinksorlights

up:batteryisloworalmostat.Chargethebatter-

ies.Wheneitherofthebatterybecomeslow,the

redlampblinksevenoneofthebatteriesisfull.

Green Red

• Greenlampandredlampblinkalternately:thetool

detectsbreakingofwire.Checktheconnection

cordforlooseconnectionwiththeswitchboxand

theshears.Ifthelampsstillblinkalternately,stop

using the tool immediately, disconnect the connec-

tion cord, remove the battery, and ask your local

authorizedservicecenterforrepair.

Lamps blink alternately

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing the battery holder into the

backpack

►Fig.9: 1. Clamp 2. Battery holder 3. Strap

1. Pass the switch box through the opening (either

rightorleft)ofthebackpack.

2. Passtheclampthroughthesquareholeofthebat-

tery holder, and secure the battery holder with the strap.

Make sure that the battery holder sits in the backpack

rmly.

Installing the holster

►Fig.10: 1. Holster 2. Strap

Passthebeltofthelowerbucklethroughtheopeningof

the holster.

Adjusting the harness

Adjusttheharnessasfollows:

1. Closeandlockthelowerbuckle,andadjustitsbelt

length.

►Fig.11: 1. Lower buckle

2. Adjusttheshoulderstraplength.

►Fig.12

3. Adjustthepositionoftheupperbuckle.Closeand

locktheupperbuckleandadjustitsbeltlength.

►Fig.13: 1.Upperbuckle

CAUTION: In case of emergency, quickly

open the lower buckle and upper buckle, loosen

shoulder straps, and set down the backpack.

Installing the connection cord

CAUTION: Always make sure that the switch

box's I/O switch is on the "O" side before attach-

ing the connection cord.

CAUTION: Do not operate the tool if the con-

nection cord is damaged.

NOTICE: Do not abuse the connection cord. Do not

carry the tool by pulling the connection cord. Keep the

connectioncordawayfromheat,oil,orsharpedges.

Otherwise the connection cord may be damaged.

Attach the connection cord with the switch box and the

shearsasfollows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar AR-3733 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info