Bedienungsanleitung Dolmar PC-7614V (Seite 8 von 52) (Englisch, Holländisch)

507712

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Cutting metals

IMPORTANT!

Always wear approved respiratory protection!

Materials that can release toxic substances may be cut only after notifying the

proper authorities and under their supervision or that of a person appointed

by them.

CAUTION:

The rapid rotation of the cutting disc heats metal and melts it at the point of

contact. Swing the guard as far down as possible behind the cut (19) in order

to direct the stream of sparks forward, away from the operator (re hazard).

Determine the direction of cutting, mark the cut and apply the disc to the material -

at moderate speed, to cut a guide groove before going to top speed and applying

more pressure to the Power Cutter.

Keep the disc straight and vertical. Do not tip it, as this can break it. -

The best way to get a good, clean cut is to pull or move the Power Cutter back -

and forth. Do not simply press the disc into the material.

Thick round stock is best cut in stages (20). -

Thin tubing and pipes can be cut with a simple downward cut. -

Cut large-diameter pipes as for round stock. To prevent tipping and for better -

control, do not let the disc sink too deeply into the material. Instead, always cut

shallow around the whole piece.

Worn discs have a smaller diameter than new discs, so that at the same engine -

speed they have a lower effective circumferential speed and therefore do not cut

as well.

Cut I-beams and L-bars in steps; see Figure 21. -

Cut bands and plates like pipes: along the wide side with a long cut. -

When cutting material under stress (supported material or material in structures), -

always make a notch in the thrust (pressure) side, and then cut from the tension

side, so that the disc does not lock in. Secure cutoff material from falling!

CAUTION:

If there is a chance that the material is under stress, be prepared for it to kick

back. Make sure you can get out of the way if you have to!

Be particularly careful in scrap-metal yards, junkyards, at accident sites,

and with haphazard piles of material. Precariously balanced pieces or pieces

under stress can act in unpredictable ways, and may slide, jump out, or burst.

Secure cutoff material from falling! Always exercise extreme caution and use

only equipment that is in perfect working order.

Observe the accident-prevention rules and regulations of your employer and/

or insurance organization.

Cutting masonry and concrete

IMPORTANT!

Always wear approved respiratory protection!

Asbestos and other materials that can release toxic substances may be cut

only after notifying the proper authorities and under their supervision or that

of a person appointed by them. When cutting prestressed and reinforced

concrete piles, follow the instructions and standards of the responsible

authorities or the builder of the structural member. Reinforcement rods must

be cut in the prescribed sequence and in accordance with applicable safety

regulations.

NOTE:

Mortar, stone, and concrete develop large quantities of dust during cutting. To

increase the lifetime of the cutting disc (by cooling), to improve visibility, and to

avoid excessive dust creation, we strongly recommend wet cutting instead of dry

cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar PC-7614V Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info