Bedienungsanleitung Dolmar PC-7614V (Seite 9 von 52) (Englisch, Holländisch)

507712

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water.

DOLMAR offers the right accessories for all wet cutting applications (see also

“SPECIAL ACCESSORIES”).

Remove foreign objects such as sand, stones and nails found within the working -

area. CAUTION: Watch out for electric wires and cables!

The rapid rotation of the cutting disc at the point of contact throws fragments

out of the cut groove at high speed. For your safety, swing the protection

hood down as far as possible behind the cut (23), so that material fragments

are thrown forward, away from the operator.

Mark the cut, and then make a groove about 5 mm (just under 1/5”) along the -

entire length of the planned cut. This groove will then guide the Power Cutter

accurately guring the actual cutoff.

NOTE:

For long, straight cuts we recommend using a trolley (24, see also “SPECIAL

ACCESSORIES”). This makes it much easier to guide the unit straight.

Perform the cut with a steady back-and-forth motion. -

When cutting slabs to size, you need not cut through the entire material thickness -

(creating unnecessary dust). Instead, simply make a shallow groove, and then

knock off the excess material cleanly on a at surface (25).

CAREFUL!

When cutting into lengths, cutting through material, making cutouts, etc., always

make sure to plan the direction and sequence of cuts in such a way that the disc

does not get jammed by the cut-off piece, and that no persons can be injured by

falling pieces.

Transport and storage

Always turn off the Power Cutter when transporting it or moving it from -

place to place on a site (26).

Never carry or move the unit with the engine on or the disc moving! -

Carry the unit only by the tubular (middle) handle with the cutting disc pointing -

behind you (26). Avoid touching the exhaust mufer (burn hazard!)

When moving the Power Cutter over longer distances, use a wheelbarrow or -

wagon.

When transporting the Power Cutter in a vehicle, make sure it is securely -

positioned in such a way that no fuel can leak out.

Always remove the cutting disc before transporting the unit in a vehicle.

The Power Cutter should be stored safely in a dry place. It must not be left -

outdoors! Always dismount the cutting disc before storage. Keep the Power

Cutter away from children.

Before long-term storage and before shipping the Power Cutter, follow the -

instructions in the chapter on “Storage”. ALWAYS empty the fuel tank and

run the carburetor dry.

When putting cutting discs in storage, be careful to: -

Clean and dry them well. -

Store them lying down at. -

Avoid dampness, freezing temperatures, direct sunshine, high temperatures and -

temperature uctuations, as these can cause breakage and splintering.

Always check new cutting discs or cutting discs that have been in storage -

to make sure that they are free of defects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar PC-7614V Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info