Bedienungsanleitung Dolmar PM-5120 S (Seite 11 von 24) (Englisch, Holländisch)

507686

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

especially heavy cutting in thick grass it may be

necessary to use one of the slowest speeds in order to get

a clean well mowed cut. When mowing long grass you

may have to cut the lawn in two passes, lowering the

blade another 1/3 of the length for the second cut and

perhaps cutting in a different pattern than was used the

first time. Overlapping the cut a little on each pass will

also help to clean up any stray clippings left on the lawn.

The mower should always be operated at full throttle to

get the best cut and allow it to do the most effective job of

mowing. Clean underside of deck. Be certain to clean the

underside of the cutting deck after each use to avoid a

build-up of grass, which would prevent proper mulching.

Mowing leaves. The mowing of leaves can also be

beneficial to your lawn. When mowing leaves make sure

they are dry and are not laying too thick on the lawn. Do

not wait for all the leaves to be off the trees before you

mow.

WARNING: If you strike a foreign object, stop the

engine. Remove wire from spark plug, thoroughly inspect

the mower for any damage and repair the damage before

restarting and operating the mower. Extensive vibration of

the mower during operation is an indication of damage.

The unit should be promptly inspected and repaired.

10-7 DECK

The underside of the mower deck should be cleaned after

each use to prevent a buildup of grass clippings, leaves,

dirt or other matter. If this debris is allowed to accumulate,

it will invite rust and corrosion, and may prevent proper

mulching. The deck may be cleaned by tilting the mower

and scraping clean with a suitable tool (make certain the

spark plug wire is disconnected).

11. MAINTENANCE

INSTRUCTIONS

SPARK PLUG

Use only original replacement spark plug. For best results,

replace the spark plug every 100 hours of use.

12. LUBRICATION INSTRUCIONS

CAUTION: DISCONNECT SPARK PLUG

BEFORE SERVICING.

1. WHEELS-Lubricate the ball bearings in each wheel at

least once a season with a light oil.

2. ENGINE-Follow engine manual for lubrication

instructions.

3. BLADE CONTROL-Lubricate the pivot points on the

blade control handle and the brake cable at least once

a season with light oil. The blade control must operate

freely in both directions.

13. CLEANING

CAUTION: Do not hose engine. Water can

damage engine or contaminate the fuel system.

1. Wipe deck with dry cloth.

2. Hose under deck by tilting the mower so that the spark

plug is up.

13-1 ENGINE AIR CLEANER

CAUTION: Do not allow dirt or dust to clog the air

filter foam element. The engine air cleaner element must

be serviced (cleaned) after 25 hours normal mowing. The

foam element must be serviced regularly if the mower is

used in dry dusty conditions. (Refer to ENGINE

OWNER’S MANUAL)

To CLEAN AIR FILTER

1. Remove screw. (Fig. 10A, Fig. 10B)

2. Remove cover.

3. Wash filter element in soap water. DO NOT USE

GASOLINE!

4. Air dry filter element.

5. Place a few drops of SAE30 oil on the foam filter and

squeeze tightly to remove any excess oil.

6. Reinstall filter.

NOTE: Replace filter if frayed, torn, damaged or

unable to be cleaned.

13-2 CUTTING BLADE

CAUTION: Be sure to disconnect and ground the

spark plug wire before working on the cutting blade to

prevent accidental engine starting. Protect hands by using

heavy gloves or a rag to grasp the cutting blades. Tip

mower as specified in separate engine manual. Remove

the hex bolt and washer which hold the blade and blade

adapter to the engine crankshaft. Remove the blade and

adapter from the crankshaft.

WARNING: Periodically inspect the blade

adapter for cracks, especially if you strike a foreign object.

Replace when necessary.

For best results your blade should be sharp. The blade

may be retargeted by removing it and either grinding or

filing the cutting edge keeping as close to the original

bevel as possible. It is extremely important that each

cutting edge receives an equal amount of grinding to

prevent an unbalanced blade. Improper blade balance will

result in excessive vibration causing eventual damage to

the engine and mower. Be sure to carefully balance blade

after sharpening. The blade can be tested for balance by

balancing it on a round shaft screwdriver. Remove metal

from the heavy side until it balances evenly.

Before reassembling the blade and the blade adapter to

the unit, lubricate the engine crankshaft and the inner

surface of the blade adapter with light oil. Install the blade

adapter on the engine crankshaft. Refer to Fig. 11. Place

the blade with the part number facing away from the

adapter. Align the washer over the blade and insert the

hex bolt. Tighten the hex bolt to the torque listed below:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar PM-5120 S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info