Bedienungsanleitung Dometic Elite Control DX systems (Seite 6 von 24) (Englisch)

629513

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Mounting the Display Elite Control Operations Manual

4 L-2230 ENGLISH

MOUNTING THE DISPLAY

1. Make the cut-out for the display panel. Cut-out size is 3-5/16” (8.41cm) wide by 2-3/16” (5.56cm) high.

2. Plug one end of the display cable (8-pin connector) into the upper-right socket on the circuit board in the electric box

and the other end into the back of the display panel.

3. Secure the display panel to the bulkhead using the four screws provided. Do not use a screw gun and do not over-

tighten screws when mounting, because either method may damage the display.

4. When the display is securely mounted, mount the bezel over the display frame until it snaps into place.

MOUNTING THE OPTIONAL SENSORS

REMOTE AIR SENSOR

Install the optional remote air sensor if the display can not be mounted in a proper location for accurately sensing room

temperature. Installing the remote air sensor overrides the display’s built-in sensor. The standard cable length for the remote air

sensor is 7 feet (2.1m).

1. Mount the remote air sensor in the return-air stream behind the opening of the return-air grille.

2. Plug its cable (6-pin connector) into the “ALT AIR” socket #J4 in the upper-left corner of the circuit board.

OUTSIDE AIR TEMPERATURE SENSOR

Install the optional outside air temperature sensor to monitor the temperature outside the cabin. Outside air sensor cables are

available in various lengths.

1. Mount the sensor outside but not in direct sunlight.

2. Plug its cable into the “OAT” socket #J3.

SERVICE SENSOR

Install the optional condenser coil temperature sensor into the “SERVICE/H2O” socket #J5. Use of this sensor must be enabled

via program parameter P-8, the Pump Sentry feature. See “P-8: Optional Pump Sentry” on page 9 for details.

OPERATION

OPERATOR CONTROLS AND DISPLAY PANEL

Refer to Figure 1, page 2 for the button locations and display functions listed below.

DISPLAY INDICATORS

• Auto Mode Indicator - The Auto Mode LED lights when the system is in Automatic Mode, which switches to cooling or

heating as required to satisfy the temperature set point.

• Cool Mode Indicator - The Cool Mode LED lights when the cool-only mode is selected or when the unit is in an

Automatic Mode cooling cycle.

• Heat Mode Indicator - The Heat Mode LED lights when the heat-only mode is selected or when the unit is in an

Automatic Mode heating cycle.

• Moisture Mode Indicator - The Moisture Mode LED lights when the Moisture Mode is selected. This mode controls

humidity during periods when the vessel is unoccupied.

IMPORTANT

The system’s air sensor is located in the control’s display panel, therefore the display MUST be located on an interior

wall at eye level. It must NOT be located in direct sunlight or inside a cabinet.

If these conditions cannot be met, you must purchase the Optional Remote Air Sensor and install it in the return-air

stream.

NOTE

Do not staple any sensor cables when mounting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dometic Elite Control DX systems Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info