Bedienungsanleitung Dremel 8200 (Seite 23 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488595

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

When the indicator light stops “BLINKING” (and becomes a

steady green light) fast charging is complete. The battery pack is

fully charged and can be removed from the charger.

When you begin the charging process of the battery pack, a

steady green light could also mean the battery pack is too hot

or too cold.

Fast charging is only possible when the temperature range of

the battery pack is between 0°C and 45°C.

When needed, the internal fan of the charger will turn on to aid

the charging process and speed.

As soon as the battery pack reaches the correct temperature

range, the battery charger will automatically switch to fast

charging.

The battery pack may be used even though the light may still

be blinking. The light may require more time to stop blinking

depending on temperature.

The purpose of the green light is to indicate that the battery

pack is fast-charging. It does not indicate the exact point of full

charge. The light will stop blinking in less time if the battery

pack was not completely discharged.

If the green indicator light is “ON”, the battery pack cannot

accept a charge.

GENERAL

The Dremel multitool is a high quality precision tool that can

be used to perform detailed and intricate tasks. The wide range

of Dremel accessories and attachments allow you to perform

a large variety of tasks. These include tasks such as sanding,

carving, engraving, routing, cleaning and polishing.

PICTURE 1

A . Shaft lock button

B . On/Off switch

C . Hanger

D . Battery level indicator

E . Variable speed switch

F . Battery pack

G . Battery release tabs

H . Ventilation openings

I . Housing

J . Battery pack

K . Battery release tabs

L . Shaft

M . Housing Cap

N . Collet nut

O . Collet

P . Collet wrench

COLLETS

The Dremel accessories available for the multitool come

with various shank sizes. Four size collets are available to

accommodate the different shank sizes. Collet sizes are

identiﬁed by the rings on the back of the collet.

PICTURE 2

A . Collet nut

B . 3.2 mm Collet without ring (480)

C . 2.4 mm Collet with three rings (481)

D . 1.6 mm Collet with two rings (482)

E . 0.8 mm Collet with one ring (483)

F . Indentiﬁcation rings

NOTE: Some multitool kits may not include all four collet sizes.

Collets are available separately.

Always use the collet that matches the shank size of the

accessory you plan to use. Do not force a larger diameter shank

into a smaller collet.

CHANGING COLLETS

PICTURE 3

A . Collet wrench

B . Shaft lock button

C . Collet nut

D . To loosen

E . To tighten

1 . Press the shaft lock button, hold down and rotate the shaft

by hand until it engages the shaft lock. Do not engage the

shaft lock button while multitool is running.

2 . With the shaft lock button engaged, loosen and remove the

collet nut. Use the collet wrench if necessary.

3 . Remove the collet by pulling it free from the shaft.

4 . Install the appropriate size collet fully into the shaft and

reinstall the collet nut ﬁnger tight. Do not fully tighten the

nut when there is no bit or accessory installed.

CHANGING ACCESSORIES

1 . Press the shaft lock button and rotate the shaft by hand

until it engages the shaft lock. Do not engage the shaft lock

button while multitool is running.

2 . With the shaft lock button engaged, loosen (do not remove)

the collet nut. Use the collet wrench if necessary.

3 . Insert the bit or accessory shank fully into the collet.

4 . With the shaft lock button engaged, ﬁnger tighten the collet

nut until the bit or accessory shank is gripped by the collet.

NOTE: Be sure to read the instructions supplied with your Dremel

accessory for further information on its use.

Use only Dremel tested, high performance accessories.

BALANCING ACCESSORIES

For precision work, it is important that all accessories be in good

balance (much the same as the tires on your automobile). To

true up or balance an accessory, slightly loosen collet nut and

give the accessory or collet a 1/4 turn. Re tighten collet nut and

run the Rotary Tool. You should be able to tell by the sound and

feel if your accessory is running in balance. Continue adjusting

in this fashion until best balance is achieved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 8200 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info