Bedienungsanleitung Dremel 8200 (Seite 24 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488595

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

USE

GETTING STARTED

The ﬁrst step in using the multitool is to get the "feel" of it. Hold

it in your hand and feel its weight and balance. Feel the taper of

the housing. This taper permits the tool to be grasped much like

a pen or pencil.

Always hold the tool away from your face. Accessories can be

damaged during handling and can fly apart as they come up to

speed.

When holding tool, do not cover the ventilation openings with

your hand. Blocking the ventilation openings could cause the

motor to overheat.

IMPORTANT! Practice on scrap material ﬁrst to see how the

tool’s high-speed action performs. Keep in mind that your

multitool will perform best by allowing the speed, along with

the correct Dremel accessory and attachment, to do the work

for you. Do not put pressure on the tool during use, if possible.

Instead, lower the spinning accessory lightly to the work surface

and allow it to touch the point at which you want to begin.

Concentrate on guiding the tool over the work using very little

pressure from your hand. Allow the accessory to do the work.

Usually it is better to make a series of passes with the tool

rather than to do the entire job with one pass. A gentle touch

gives the best control and reduces the chance of error.

HOLDING THE TOOL

For best control in close work, grip the multitool like a pencil

between your thumb and foreﬁnger. PICTURE 4

The "golf" grip method is used for heavier operations such as

grinding or cutting. PICTURE 5

OPERATING SPEEDS

To select the right speed for each job, use a practice piece of

material.

SLIDE "ON/OFF" SWITCH

The tool is switched "ON" by the slide switch located on the

topside of the motor housing.

TO TURN THE TOOL "ON", slide the switch button forward.

TO TURN THE TOOL "OFF", slide the switch button backward.

HIGH PERFORMANCE MOTOR

Your tool is equipped with a high performance rotary tool motor.

This motor expands the versatility of the rotary tool by driving

additional Dremel attachments.

ELECTRONIC MONITORING

Your tool is equipped with an internal electronic monitoring

system that provides a “soft start”, which will reduce the

stresses that occur from a high torque start. The system also

helps to maximize motor and battery performance by cutting

the voltage to the tool when stall conditions (see section “Stall

Protection”) occur. The motor and battery pack are protected by

cutting back the voltage to the motor in these situations.

VARIABLE SPEED SLIDE SWITCH

Your tool is equipped with a variable speed slide switch. The

speed may be adjusted during operation by sliding the switch

back or forth between any one of the settings.

The speed of Rotary Tool is controlled by setting this dial on the

housing. PICTURE 6

Settings for Approximate Revolutions

Switch Setting Speed Range

5 5000-7000 min

–1

10 7000-10000 min

–1

*15 13000-17000 min

–1

20 18000-23000 min

–1

25 23000-27000 min

–1

30 28000-30000 min

–1

* Do not exceed 15000 min

–1

when using wire brushes.

Refer to the Speed Settings chart on pages 4-7 to help

determine the proper speed for the material being worked on

and the accessory to use.

Most jobs can be accomplished using the tool at the highest

setting. However, certain materials (some plastics and metals)

can be damaged by high-speed generated heat and should

be worked on at relatively low speeds. Low speed operation

(15000 min

–1

or less) is usually best for polishing operations

employing the felt polishing accessories. All brushing

applications require lower speeds to avoid wire discharge from

the holder. Let the performance of the tool do the work for you

when using lower speed settings. Higher speeds are better for

hardwoods, metals and glass and for drilling, carving, cutting,

routing and shaping.

Some guidelines regarding tool speed:

• Plastic and other materials that melt at low temperatures

should be cut at low speeds.

• Polishing, bufﬁng and cleaning with a wire brush must be

done at speeds no greater than 15000 min

–1

to prevent

damage to the brush and your material.

• Wood should be cut at high speed.

• Iron or steel should be cut at high speed.

• If a high speed steel cutter starts to vibrate, it usually

indicates that it is running too slowly.

• Aluminium, copper alloys, lead alloys, zinc alloys and tin

may be cut at various speeds, depending on the type of

cutting being done. Use a parafﬁn (not water) or other

suitable lubricant on the cutter to prevent the cut material

from adhering to the cutter teeth.

NOTE: Increasing pressure on the tool is not the answer when

it is not performing properly. Try a different accessory or speed

setting to achieve the desired result.

STALL PROTECTION

This tool has a stall protection feature built into it to protect the

motor and battery in the event of a stall. If you put too much

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 8200 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info