801276
26
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
26
Instructions for use ST4D 2G / ST4D 2G PLUS
Drive Medical GmbH & Co. KG | As per: 04.05.2020 | Errors and alterations excepted
EN
Number of
blinks Error Eect on the
scooter Comments
1Battery weak Scooter slow The charge status of the batteries is low. Charge the
batteries as soon as possible.
2 Battery voltage is too low Driving is not
possible
The charge status of the batteries is empty. Charge
the batteries as soon as possible. Check the battery,
connections, and cables.
3 Battery voltage is too high Driving is not
possible
The charge status of the batteries is too high. Causes
can include excessive charging and/or descending a
hill (since in this case the batteries are automatically
charged). When descending a hill, reduce the speed
in order to not charge the battery further. Switch the
scooter o and back on.
4Time limit for maximum
current limit exceeded or
control unit too hot
Driving is not
possible
The scooter has consumed too much current for an
overly long period of time, which could be attributed to
an excessive load, jamming, or the throttling of the motor.
Switch the scooter o and wait a few minutes before
switching it on again. The control unit has discovered a
short circuit in the motor. Check the cable harness for
short-circuited electrical circuits and check the motor.
Contact your customer service.
5Brake error Driving is not
possible
Check whether the gearshift lever for the parking brake
is in the locked position. The brake coil or the cables
of the parking brake are defective. Check the parking
brake and the cables for short-circuited electrical circuits
or exposed cables. Contact your customer service.
6 Driving is blocked Driving is not
possible
A STOP function is enabled or a charge blocking has
occurred. Disable the STOP function and separate the
charging unit from the scooter. Bring the control lever
into a neutral position and switch the scooter o and
back on. The control lever may need to be recalibrated.
Check the cables of the control lever.
7Error of the rotational
speed potentiometer
Driving is not
possible
The control lever or its cable is defective. Check
exposed cables or short-circuited electrical circuits. The
control lever could be incorrectly adjusted. Contact your
customer service.
8Motor voltage error Driving is not
possible
The motor or its cable is defective. Check exposed
cables or short-circuited electrical circuits. Contact your
customer service.
9Other defect Driving is not
possible
The control unit may be internally defective. Check
exposed cables or short-circuited electrical circuits.
Contact your customer service.
If the red LED in the battery display is blinking, the error can be determined using the blink code:
Error code description control unit Rhino 2
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Drive ST4D 2G PLUS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info