Bedienungsanleitung Drive ST4D 2G (Seite 26 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

801275

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Instructions for use ST4D 2G / ST4D 2G PLUS

Drive Medical GmbH & Co. KG | As per: 04.05.2020 | Errors and alterations excepted

Number of

blinks Error Eect on the

scooter Comments

1Battery weak Scooter slow The charge status of the batteries is low. Charge the

batteries as soon as possible.

2 Battery voltage is too low Driving is not

possible

The charge status of the batteries is empty. Charge

the batteries as soon as possible. Check the battery,

connections, and cables.

3 Battery voltage is too high Driving is not

possible

The charge status of the batteries is too high. Causes

can include excessive charging and/or descending a

hill (since in this case the batteries are automatically

charged). When descending a hill, reduce the speed

in order to not charge the battery further. Switch the

scooter o and back on.

4Time limit for maximum

current limit exceeded or

control unit too hot

Driving is not

possible

The scooter has consumed too much current for an

overly long period of time, which could be attributed to

an excessive load, jamming, or the throttling of the motor.

Switch the scooter o and wait a few minutes before

switching it on again. The control unit has discovered a

short circuit in the motor. Check the cable harness for

short-circuited electrical circuits and check the motor.

Contact your customer service.

5Brake error Driving is not

possible

Check whether the gearshift lever for the parking brake

is in the locked position. The brake coil or the cables

of the parking brake are defective. Check the parking

brake and the cables for short-circuited electrical circuits

or exposed cables. Contact your customer service.

6 Driving is blocked Driving is not

possible

A STOP function is enabled or a charge blocking has

occurred. Disable the STOP function and separate the

charging unit from the scooter. Bring the control lever

into a neutral position and switch the scooter o and

back on. The control lever may need to be recalibrated.

Check the cables of the control lever.

7Error of the rotational

speed potentiometer

Driving is not

possible

The control lever or its cable is defective. Check

exposed cables or short-circuited electrical circuits. The

control lever could be incorrectly adjusted. Contact your

customer service.

8Motor voltage error Driving is not

possible

The motor or its cable is defective. Check exposed

cables or short-circuited electrical circuits. Contact your

customer service.

9Other defect Driving is not

possible

The control unit may be internally defective. Check

exposed cables or short-circuited electrical circuits.

Contact your customer service.

If the red LED in the battery display is blinking, the error can be determined using the blink code:

Error code description control unit Rhino 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Drive ST4D 2G Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info