Bedienungsanleitung DRU ART 8-02 (Seite 12 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810302

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Foreword

Dear Customer,

We would like to thank you for buying this DRU prod-

uct. Our products have been designed and produced to

meet the highest possible quality, performance and safety

requirements, allowing you to enjoy years of problem-free

use.

In this booklet you will find instructions for the installation

and use of your new appliance. Please read these instruc-

tions and the manual carefully to familiarize yourself with

the appliance. If you require any further support, please do

not hesitate to contact your supplier.

Unpacking

Once the heater has been unpacked, all packaging should

be disposed of in the regular manner.

Connection

This appliance should be connected by a registered installer.

INSTRUCTIONS FOR INSTALLATION

Type of gas

This appliance can only be used and is only suitable for the

country and the type of gas mentioned on the type iden-

tification tag. Please check that the local gas and pressure

correspond with the specifications on the type identifica-

tion tag. All regulations regarding gas installation, includ-

ing any local regulations, must be observed at all times.

Installation and maintenance of the appliance should be

performed by a professional certified expert with proven

knowledge and demonstrable competence in this field. A

professional expert takes all technical aspects such as heat

output and gas connection into account, as well as the flue

gas discharge requirements. The installation manual will

give you the information you need to install the appliance

in such a way that it will operate properly and safely. If the

installation instruction is not clear, national/local regula-

tions must be observed.

To operate the heater suitable for natural gas on propane,

it should be converted by a competend person. A conver-

sion set can be ordered through your

supplier.

Important

• Keep curtains and any other flammable materials at least

50cm away form the appliance.

• Caution! Touching the heater when hot can cause burns

and blisters!

• The appliance should be installed and maintained by a

registered installer.

• Do not install any so-called dust filter on or under the

casing.

• Do not hang wet clothes and towels etc. on the heater

to dry.

• The appliance was designed for atmospheric and heating

purposes. This means that all visible surfaces, including the

glass pane, can become hotter than 100C°. It is recom-

mended to always place a protective grating in front of

the appliance when there are children, elderly people or

handicapped persons in the same room as the appliance.

If it is possible that vulnerable people are regularly present

in the room with no supervision, a fixed guard should be

mounted around the appliance.

• When installing the appliance, check the air circulation

(by convection) around the thermostat sensor. If there is

a lack of air circulation, the sensor must be moved to a

position with sufficient air circulation for correct opera-

tion of the appliance.

General

The appliance can be mounted either on a wall of incombu-

stible material (e.g. stone or concrete) or on a wall of com-

bustible material (e.g. wood).

Art 2-01,3-01 and 4-01 on propane (G31) can be placed

in vehicles pulling mobile units, provided the following is

observed:

• When the appliance is working, the mobile unit must be

standing still;

• When the vehicle pulling the mobile unit is being filled

with fuel, the appliance must be switched off;

• If glass is broken, switch off the appliance and contact an

installer;

• In case of a gas leak, switch off the appliance as well as the

gas supply tap and contact an installer;

• Flue gas discharge must remain unobstructed at all times.

Installation to a wall of non-flammable material

(fig. 7, 9, 11, pg. 50-52)

ART Models 2-01, 3-01 and 4-01 can are suitable for

hanging installation only, ART Models 5-01, 6-01, 8-02

and 10-02 are suitable for either hanging or freestanding

installation. Allow at least 1 metre’s clearance above the

heater to enable sufficient heat circulation. When installed

hanging, at least 1 m free space should be kept above the

appliance to allow sufficient heat dissipation.

When intalled standing, the bottom of the mounting sheet

(2) should stand on the floor, this is the minimum height

between the floor and centre of wall duct

(size F. fig 7, 9, 11, pg. 50-52).

The mounting plate (2) serves as a template to mark the

position of the duct. To be able to hang the casing over the

interior, a minimal clearance of 25 mm must be allowed

between the appliance and a windowsill or suchlike. The

minimum clear installation height (Y) required for each of

the various models is listed in the table on page 53.

The standard wall duct

Drill a horizontal hole in the wall, ø E to take the air-supply

pipe. The wall duct should slope at an angle of approx. 2º.

INSTRUCTIONS FOR INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU ART 8-02 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info