Bedienungsanleitung DRU ART 8-02 (Seite 14 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810302

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

This prevents possible dirt and deposit from settling onto

the wall. Take the interior and put it with the bottom

edge on the two supports of the mounting sheet. Keep

the interior balanced and slide the outlet pipe a little bit

into the outlet opening of the interior for support. Now

slide the interior against the mounting sheet, taking care

that the turned-back edge of the mounting sheet fits into

the inlet bush on the back side of the interior and that

the bolts (10) stick through the clamps (11). Attach screw

nuts and washers to the bolts (10) and tighten closely up

to the stop. Then slide the screw spindle (12) into the

clamp (13). Fix the screw nut and washer to the screw

spindle (12) and tighten until the interior is standing paral-

lel to the wall.

N.B. If easy accessible, e.g. on the ground floor, the outlet

pipe can also be mounted from the outside after the grid

interior sheet and the basket have been disassembled.

ART 3-01 and 4-01:

After fitting heat-exchanger fix thermostat phial in clip

provided at rear of backplat (R.H.S.).

Connection of the gas supply

For the different types are the connections as mentioned

below:

• ART 2-01, 5-01, 6,-01, 8-02, 10-02 3/8” inner thread

• ART 3-01, 4-01 3/8” outer thread

If the supply pipe enters the appliance through the back

plate, press out the disc in the plate. An approved con-

necting tap with coupling should be used in the supply

pipe (For Belgium this should be B.G.V. approved). The

connecting tap with coupling should be fitted outside the

casing. Furthermore:

• Expel all air from the supply pipes/hoses before coupling

to the appliance.

• Do not turn the coupling tap when connecting it to the

gas supply.

• Avoid any pressure on the control tap and pipes.

• Check that all connections are gastight.

Operations

The manufacturer has made the appliance suitable for

the type of gas as indicated on the type identification tag.

Check that the gas pre-pressure and burner pressure cor-

respond with what is stated on the type plate. If necessary,

use the control screw to correct the burner pressure. The

control screw for burner pressure is located behind the

cover on the gas control. This cover can be removed by

removing the screw and clicking loose the lip on the left

side by means of a screwdriver. The thermostat regulates

modulatingly between “full power setting” and “low power

setting” and , when little heat is required, in two settings,

i.e. “low” or “off”. In this situation, the pilot light keeps

burning. The “low” setting can only be checked when the

room temperature is higher than

± 15°C (60°F).

The low setting

The low setting has been adjusted to ± 20% of the full

consumption. The low setting screw has been fully tight-

ened and is supplied with the correct low setting bore.

This is not adjustable.

Pilot light burner

Upon delivery, the pilot light burner has the correct con-

sumption by means of a nozzle inside the pilot light burner.

The pilot light burner needs no adjustment.

Putting the casing in its place

From the top, hang the casing over the back sheet, taking

care that the hooks of the casing fit into the notches of

the back sheet and that the operating buttons fit into the

appropriate opening in the casing.

INSTRUCTIONS FOR INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU ART 8-02 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info